ASSEMBLY INSTRUCTIONS
STEP 1)
First place the bo om panel on the ground. Your sauna should always be placed on a level surface and in a dry area with about 4 feet away from a power
outlet.
STEP 2)
Next, place the back panel on top of the floor panel; carefully and firmly line up the back panel on the groove of the bo om panel.
Remove protec-ve tape and then fasten buckle...
STEP 3)
Then place the right panel, when posi-oning the right panel on top of the floor panel, secure the bo om first and then the side by adjus-ng tongue &
groove; check that it lines up correctly; remove tape and then fasten buckle.
STEP 4)
Con-nue by placing the le2 panel on top of the floor panel, posi-on correctly in tongue & groove by star-ng with the bo om and then the side; align the
buckles on the panels, remove tape and fasten them. Next is the top back panel…
STEP 5)
Before connec-ng the top back panel to the bo om panel, pull-down the electric cable from the top
panel into the bo om panel, all the way, then, pull-out the cable at the base.
STEP 6)
Next, connect the right top panel to the bo om right panel; buckle and secure.
STEP 7)
Repeat this for the le2 top panel to the bo om le2 panel. Make sure that all buckles are properly
secured on all panels.
STEP 8)
At this stage heaters are now introduced in the cabin to be placed on the walls and the
bench panel.
First, insert the electric cable through the cable hole. And pull out from beneath.
STEP 9)
Then a ach the heaters by adjus-ng loop into the screw, star-ng with the bo om. And then top.
STEP 10)
Then, place power box inside the sauna cabin.
Screw in to secure on bo om panel with PWA3* screws.
STEP 11)
Connect the top panel cable to the power supply box and secure -ghtly.
Push out electric cable through the plug hole in the base of the sauna and connect it to the power outlet on wall, then place
cap back into place.
STEP 12)
Slide down the bench heater panel by lining up its sides with the ver-cal guides on each side panel.
Push the bench heater panel all the way down un-l it’s touching the bo om panel and securely in place.
STEP 13)
Install the bench seat panel at an angle sliding in horizontally. Push the panel all the way in un-l it touches the
back panel and is securely in place be careful not to scratch other panels or heaters.
STEP 14)
Now, con-nue by moun-ng the back rest over the heaters and connec-ng the bo om front window door panel
to the floor and side panels. Posi-on into place firmly. Followed by the top front window door panel.
STEP 15)
Locate the door handle and a ach to the door. The unfinished side of the door handle should face the inside of
the cabin while the finished side of the door handle should be outside the sauna.
STEP 16)
Then, place the wooden sauna sealing blocks horizontally on the inside of the door wall, next to the door edges
to cover the edge of the top and bo om panels.
STEP 17)
Lastly, gently lower and screw the roof panel.
YOUR SAUNA IS NOW COMPLETELY ASSEMBLED!
*** A ach op-onal accessories; Color Lights and Oxygen Ionizer
Place the light bulb over the installed light fixture and oxygen ionizer in place.
You can get the most out of your sauna experience with these far infrared sauna and conven-onal sauna accessories.
STEP 1
STEP 2
STEP 3
STEP 4
STEP 10
STEP 17
STEP 5
STEP 6
STEP 11
STEP 12
STEP 13
STEP 7
STEP 9
STEP 8
STEP 16
STEP 15
STEP 14
1
2
3
4
1.
Pull down
2.
Insert
3.
Adjust Tongue & Groove
4.
Pull out from below