JLG 3513PS Operation & Safety Manual Download | Manualshive

Page: 62 / 70

background image

Section 9 - Specifications

9-2

31200345

Dimensions

Platform Overall Height

Fixed Platform..........................................................................................................1630 mm (64.2 in)
Extendable Platform..............................................................................................1626 mm (64.0 in)

Platform Overall Length

Fixed Platform..........................................................................................................1907 mm (75.1 in)
Extendable Platform..............................................................................................2292 mm (90.2 in)

Platform Overall Width

Fixed Platform..........................................................................................................1829 mm (72.0 in)
Extendable Platform

Retracted ...........................................................................................................2440 mm (96.1 in)
Extended......................................................................................................... 4525 mm (178.1 in)

Overall Length of Machine with Platform Attached

3513PS & 4013PS

Fixed Platform ........................................................................................................7,59 m (24.9 ft)
Extendable Platform ............................................................................................7,97 m (26.1 ft)

4014PS

Fixed Platform ........................................................................................................8,06 m (26.5 ft)
Extendable Platform ............................................................................................8,46 m (27.8 ft)

4017PS

Before S/N 1160006867

Fixed Platform ................................................................................................7,70 m (25.3 ft)
Extendable Platform ....................................................................................8,09 m (26.5 ft)

S/N 1160006867 & After

Fixed Platform ................................................................................................8,33 m (27.3 ft)
Extendable Platform ....................................................................................8,71 m (28.6 ft)

Platform Working Area

Width

Fixed Platform .............................................................................................................1,8 m (5.9 ft)
Extendable Platform .............................................................................................. 4,5 m (14.8 ft)

Length

Fixed Platform .......................................................................................................... 0,76 m (2.5 ft)
Extendable Platform .............................................................................................. 1,04 m (3.4 ft)

«
...
60
61
62
63
64
...
»

Summary of Contents for 3513PS







































































Reviews:

No comments

Related manuals for 3513PS

Brand: ABB Pages: 138

Brand: ABB Pages: 116

Brand: Migatronic Pages: 28

Xenta 400 Series

Brand: TAC Pages: 48

IDEALARC CV-250

Brand: Lincoln Electric Pages: 42

Brand: Faraone Pages: 68

Brand: GYS Pages: 60

Brand: M-system Pages: 3

Brand: YASKAWA Pages: 116

Brand: GCAN Pages: 12

Brand: Measurement Computing Pages: 50

Robopac Rotoplat 3000LD

Brand: AETNAGROUP Pages: 87

Brand: NI Pages: 28

Brand: OTC DAIHEN EUROPE Pages: 73

Brand: Puhui Pages: 13

Brand: MAHA Pages: 28

Brand: MANDREL welder Pages: 36

Brand: Argus Pages: 38

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands