JLA D90 Installation Manual Download Page 38

Page: 38 / 40

JLA Limited

113374 - 4

Input/Output (I/O) Board Output Description (“Green” light emitting diode [L.E.D.])

1. FAN – (GREEN L.E.D.)

This L.E.D. will indicate the status of the Fan output. If the request to turn on the
Fan (blower) is made, then the L.E.D. is ON.

2. FWD – (GREEN L.E.D.)

This L.E.D. will indicate the status of the Basket (Tumbler) Forward direction output.

If the request to tumble the drum in the Forward direction is made, then the L.E.D.
is ON.

3. REV – (GREEN L.E.D.)

This L.E.D. will indicate the status of the Basket (Tumbler) Reverse direction output.

If the request to tumble the drum in the Reverse direction is made, then the L.E.D.
is ON.

4. AIR JET – (GREEN L.E.D.)

This L.E.D. will indicate the status of the Air Jet output. If the request to turn on the
Air Jet is made, then the L.E.D. is ON.

5. HEAT – (GREEN L.E.D.)

This L.E.D. will indicate the status of the Front Heat output. If the request to turn
on the Front Burner is made, then the L.E.D. is ON.

6. STEAM – (GREEN L.E.D.)

This L.E.D. will indicate the status of the Steam Injection output. If the request to
turn on the Steam Injection is made, then the L.E.D. is ON.

7. AUX – (GREEN L.E.D.)

This L.E.D. will indicate the status of the fire suppression system output. If the
request to turn on the fire suppression system is made, then the L.E.D. is ON.

Input/Output (I/O) Board Input Description (“Red” L.E.D.)

8. FUSE – (RED L.E.D.)

This L.E.D. will indicate the status of the (F2), which fuses the 24 VAC supplied to
the board.

9. LINT – (RED L.E.D.)

This L.E.D. will indicate the status of the Lint Drawer. If the drawer is closed, then
the L.E.D. is ON.

10. MAIN – (RED L.E.D.)

This L.E.D. will indicate the status of the Front Doors. If the doors are closed, then
the L.E.D. is ON.

11. EXHL – (RED L.E.D.)

This L.E.D. will indicate the status of the Exhaust Hi-Limit Disk. If the disk is
closed (Temperature below 225º F [107º C]), then the L.E.D. is ON.

12. SAIL – (RED L.E.D.)

This L.E.D. will indicate the status of the Sail Switch. If the switch is closed, then
the L.E.D. is ON.

13. BRHL – (RED L.E.D.)

This L.E.D. will indicate the status of the Burner Hi-Limit Disk. If the disk is closed

(Temperature below 330º F [166º C]), then the L.E.D. is ON.

14. GAS_V – (RED L.E.D.)

This L.E.D. will indicate the status of the Gas Valve. If the Gas Valve is open (ON),
then the L.E.D. is ON.

15. ESTOP – (RED L.E.D.)

This L.E.D. will indicate the status of the Emergency Stop Switch. If the Emergency

Stop Switch is open (ON), then the L.E.D. is ON.

OUTPUTS: (GREEN)

FAN - Blower Fan On

FWD - Basket (Tumbler) Forward

REV - Basket (Tumbler) Reverse

AIR JET - Air Jet On

HEAT - Front Heat

STEAM - Steam Injection

AUX - Fire Suppression System (F.S.S.) Active On

INPUTS: (RED)

FUSE - 24 VAC To Board (F2)

LINT - Lint Drawer Closed

10. MAIN - Main Door Closed

11. EXHL - Exhaust High Limit

12. SAIL - Sail Switch

13. BRHL - Burner High Limit

14. GAS_V - Gas Valve

15. ESTOP - Emergency Stop

Summary of Contents for D90









































Search results

Summary of Contents for D90

Reviews:

Related manuals for D90

Brands by name

Popular brands

JLA D90, Installation Manual

Search results

Summary of Contents for D90

Reviews:

Related manuals for D90

Brands by name

Popular brands