SB-D-TRKCTR/12W3v3_INSTR_SKU#011104
S T E P 8
Place the Stealthbox
®
into the mounting location. Secure the
Stealthbox with the factory bolts that were removed in
STEP 2
.
DO NOT OVER TIGHTEN THE BOLTS
.
Slide the seat belts back through the elastic loops.
C O N G R A T U L A T I O N S
You have completed the installation for this model!
Please refer to the Power Recommendation section for an
amplifier recommendation and basic set-up help.
S T E P 7
If this truck has the seat belt retracting sensor (black box),
secure this sensor to the driver’s seat mounting leg. Make
sure that the sensor is positioned exactly the same way it
was positioned as factory installed. If not, the seat belts will
not function correctly.
Run speaker wire from the amplifier’s location to the
Stealthbox
®
location and check for proper operation of
the woofer.
S T E P 6
Fold the four black plastic strips under the upholstery.
This upholstery/strip fold is to be mounted to the
Stealthbox®.
Using a 1/8-inch drill bit and drill. Drill a pair of pilot holes into
the Stealthbox®. The pilot holes are to be in line with each of
the upholstery/strip folds.
Secure each fold with two of the supplied screws to the
Stealthbox®.
S T E P 5
In reverse of
STEP 3
.
Slide the upper arm rest section’s arms through the cutouts
in the upholstery that is wrapped around the Stealthbox®.
With an 8mm socket and the OEM bolts, secure the upper
arm rest section too the bottom cushion section.
Page 3 • JL Audio, Inc 2016
All specifications are subject to change without notice. “JL Audio®” and the JL Audio logo, “Stealthbox” and the Stealthbox logo are registered
trademarks of JL Audio, Inc. “Ahead of the Curve” and its respective logo is a trademark of JL Audio, Inc.
JLA-SKU# 011104 - 09.20.2016
• Printed in USA • ©2016 JL Audio, Inc.
For more detailed information please visit us online at
www.jlaudio.com.
(954) 443-1100
w w w. j l a u d i o . c o m
1 0 3 6 9 N O R T H C O M M E R C E P A R K W A Y • M I R A M A R , F L O R I D A • 3 3 0 2 5 • U S A
I N C L U D E D H A R D W A R E
(8)
#8 x 1/2-inch Wafer Head Screws
S P E C I F I C A T I O N S
Enclosure Type:
Acoustic Suspension (sealed)
Driver Type:
12W3v3-2
Nominal Impedance:
2 ohms
Continuous Power Handling:
500 Watts
P O W E R R E C O M M E N D A T I O N
JL Audio recommends using a high quality amplifier such as the JL Audio XD300/1.
The diagram below shows the recommended crossover settings for the XD300/1 when being used to power your
Stealthbox
®
.
The JL Audio XD300/1 is a very versatile audio component. Please consult the owner’s manual for even more
detailed information about installing and tuning this amplifier.
M I D / H I G H F R E Q U E N C Y D R I V E R F I T M E N T
A variety of JL Audio coaxial and component systems will fit in the factory speaker locations of you vehicle.
Front Speaker Size / Location:
6x9 / Front Doors
Fits JL Audio Models:
TR690-TXi, C2-690tx
Rear Speaker Size / Location:
5.25-inch / Rear Panels
Fits JL Audio Models:
TR525-CXi, C2-525x, C3-525, C5-525x
