SB-D-DRNGO2/10W3v3_INSTR_SKU#011239
SB-D-DRNGO2/10W3v3_INSTR_SKU#011239
STEALTHBOX WALL
VEHICLE SHEET METAL
THREADED INSERT
LOCK WASHER
FLAT WASHER
SOCKET CUP SET SCREW
HEX NUT
FENDER WASHER
C O N G R A T U L A T I O N S
You have completed the installation for this model!
Please refer to the Power Recommendation section for an
amplifier recommendation and basic set-up help.
S T E P 6
From driver’s side outer fender well, place a supplied fender
washer,
flat washer, lock washer and then hex nut onto the socket
cup set screw and secure.
Note: For added protection
it is recommended that you apply a bead of silicone
between the vehicle and the fender washer. After the
bolt assembly is tightly secured, it is also recommend-
ed that vehicle under-coating material is applied to
the exposed assembly
Secure the driver’s side plastic fender well, from
STEP 1
.
S T E P 5
Back out the socket cup set screw installed in
STEP 3
, to
leave 1 1/4-inch of thread exposed.
Place the Stealthbox® into position by guiding the socket cup
set screw through the hole drilled in
STEP 4
.
S T E P 4
With a drill and a 1/2-inch drill bit, drill through the
impression made in the wax square.
Note: Before drilling,
make sure that you are not going to be drilling into
any gas lines, brake lines, transmission lines, electrical
wiring, transfer case (4x4 vehicles) or anything else
that might cause a reduction in your weekly pay.
Always wear eye protection when drilling!
Remove the wax square.
Page 2 • JL Audio, Inc 2007
All specifications are subject to change without notice. “JL Audio®” and the JL Audio logo, “Stealthbox” and the Stealthbox logo are registered
trademarks of JL Audio, Inc. “Ahead of the Curve” and its respective logo is a trademark of JL Audio, Inc.
JLA-SKU#011239 -09-06-200
JLA-SKU#011239 -09-06-2007
7
• Printed in USA • ©2007 JL Audio, Inc. • U.S. PATENTS: #5,734,734 #5,949,898 #6,118,884 #6,229,902
#6,243,479 #6,294,959 #6,501,844 #6,496,590 #6,441,685 #5,687,247 #6,219,431 #6,625,292 #D472,891 #D480,709 Other U.S. & Foreign
patents pending. For more detailed information please visit us online at
www.jlaudio.com.
(954) 443-1100
w w w . j l a u d i o . c o m
1 0 3 6 9 N O R T H C O M M E R C E P A R K W A Y • M I R A M A R , F L O R I D A • 3 3 0 2 5 • U S A
I N C L U D E D H A R D W A R E
(1)
(1)
3-inch x 3-inch Wax Square
3-inch x 3-inch Wax Square
(1)
(1)
3/8-inch Fender Washer
3/8-inch Fender Washer
(1)
(1)
3/8-inch -16 x 2 1/4-inch Socket Cup Set Screw
3/8-inch -16 x 2 1/4-inch Socket Cup Set Screw
(1)
(1)
3/8-inch -16 Hex Nut
3/8-inch -16 Hex Nut
(1)
(1)
3/8-inch Split Lock Washer
3/8-inch Split Lock Washer
(1)
(1)
3/8-inch Flat Washer
3/8-inch Flat Washer
S P E C I F I C A T I O N S
Enclosure Type:
Acoustic Suspension (sealed)
Acoustic Suspension (sealed)
Driver Type:
10W3v3
10W3v3
Nominal Impedance:
4 ohms mono
4 ohms mono
Continuous Power Handling:
300 Watts
300 Watts
P O W E R R E C O M M E N D A T I O N
P O W E R R E C O M M E N D A T I O N
JL Audio recommends using a high quality amplifier such as the JL Audio 250/1v2.
The diagram below shows the recommended crossover, infrasonic filter and equalizer settings for the 250/1v2
when being used to power your Stealthbox
®
.
The JL Audio 250/1v2 is a very versatile audio component. Please consult the owner’s manual for even more
detailed information about installing and tuning this amplifier.
M I D / H I G H F R E Q U E N C Y D R I V E R F I T M E N T
A variety of JL Audio coaxial and component systems will fit in the factory speaker locations of you vehicle.
Front Speaker Size / Location:
6-inch x 9-inch / Front Doors
6-inch x 9-inch / Front Doors
Fits JL Audio Models:
*TR690-CXi & *VR690-CXi
TR690-CXi & *VR690-CXi
Rear Speaker Size / Location:
6.5-inch / Rear Door
6.5-inch / Rear Door
Fits JL Audio Models:
TR650-CXi, TR650-CSi, VR650-CXi, *XR650-CXi, *XR650-CSi,
TR650-CXi, TR650-CSi, VR650-CXi, *XR650-CXi, *XR650-CSi,
*C5-650x, *C5-650 & *ZR650-CSi
*C5-650x, *C5-650 & *ZR650-CSi
*Mounting / spacer ring is required.
*Mounting / spacer ring is required.
