background image

12 

 |  JL Audio - M600/6 Owner’s Manual  

13

D) Subwoofer Level Control Only:

 

Req uired: 

a source unit or processor with 

one pair of stereo outputs and dedicated 
subwoofer outputs. 

Inp ut Connections: 

the stereo pair of source 

unit outputs each split with a “Y-Adaptor” 
allowing the left signal to be sent to the “

CH 

1 (Left)

” and “

CH 3 (Left)

” inputs and the 

right signal to be sent to the “

CH 2 (Right)

” 

and “

CH 4 (Right)

” inputs of the M600/6. The 

source unit’s dedicated subwoofer outputs are 
connected to the “

CH 5 (Left)

” and  

CH 6 (Right)

” inputs (select “

6 Ch.

” on the 

Input Mode

” switch in the “

Channel 5 & 6 

Controls

” section). 

Res ult: 

in this mode, the user has the ability to 

control the absolute level of the LF channels 
relative to the HF channels. 

E)  Independent level control of all three  

channel pairs:

Req uired: 

a source unit or processor with 

two pairs of stereo outputs and dedicated 
subwoofer outputs. 

Inp ut Connections: 

one pair of stereo source 

unit outputs is connected to the “

CH 1 (Left)

” 

and “

CH 2 (Right)

” inputs, the second pair of 

stereo source unit outputs is connected to the 

CH 3 (Left)

” and “

CH 4 (Right)

” inputs and 

the source unit’s dedicated subwoofer output 
is connected to the “

CH 5 (Left)

” and “

CH 6 

(Right)

” inputs (select “

6 Ch.

” on the “

Input 

Mode

” switch. 

Res ult: 

in this mode, the user has the ability to 

control the absolute level of the LF channels as 
well as both pairs of HF channels. 

When using a source unit’s dedicated 

subwoofer output, set the “Input Sens.” of any 

channels receiving input from the subwoofer 

output with the source unit’s subwoofer level 

control set at 3/4 of full output. See Appendix A 

(page 14) for details.

Crossover Setup for Bi-Amplified System  

with one M600/6:

Once the input sections have been configured 

appropriately, go to the “

Channel 5 & 6 

Controls

”. Select “

LP

” (low-pass) on the “

Filter 

Mode

” switch and an appropriate “

Filter Freq.

” 

(80 Hz is a good starting point). 
Next, turn your attention to the “

Channel 1 & 

2 Controls

” and “

Channel 3 & 4 Controls

” and 

select “

HP

” (high-pass) on the “

Filter Mode

” 

switches and an appropriate “

Filter Freq.

” (again, 

80 Hz is a good starting point).

After proper adjustment of the “

Input 

Sens.

” controls for all three channel pairs 

using the method shown in Appendix A 
(page 14), you can fine tune filter frequencies 
and attenuate any pair of channels to achieve 
proper balance. For precise filter frequency 
information refer to Appendix B (page 15).

sYstem ConFigurations

The M600/6 is a flexible amplifier, well-suited 

for a multitude of system configurations. In 
this section, the most likely configurations are 
explained in detail.

Once you have selected your desired 

configuration, you can use the amplifier panel 
drawing on pages 18 & 19 to mark the required 
switch positions for easy reference. 

bi-amPliFied sYstems

Bi-amplified systems are defined as systems 

in which separate amplifier channels drive low-
frequency (LF) and high-frequency (HF) speakers 
and are separately filtered to send appropriate 
frequency ranges to each speaker system.

The most common application of 

bi-amplification in marine audio is to drive a 
subwoofer system from one or more amplifiers or 
channels and component speakers from separate 
amplifiers or channels.

The M600/6 is designed to work as the only 

amplifier in a bi-amplified system.

bi-amplified system with the m600/6

In this configuration, channels 5&6 of the 

M600/6 will drive subwoofers (stereo 75W x 2 at 
4 ohms, 100W x 2 at 2 ohms, or bridged 200W x 1 
at 4 ohms) with low-pass filtering. Channels 1&2 
and channels 3&4 will drive component speakers 
in stereo (75W x 4 at 4 ohms or 100W x 2 at 2 
ohms) with high-pass filtering.  
 

Input connection options for a bi-amplified system 
with one M600/6 are as follows: 

A) No User Adjustability:

Req uired: 

a basic source unit or processor 

with one pair of stereo outputs.

Inp ut Connections: 

a single pair of stereo source 

unit outputs is connected to the “Ch 1” and “Ch 
2” inputs of the M600/6. Then, select “

2 ch.

” on 

the M600/6’s “

Input Mode

 

switch. 

Res ult: 

the relative level of the LF and HF 

channels will be fixed by the M600/6’s “

Input 

Sens.

” settings and will not be user adjustable 

from the helm (unless an optional HD-RLC is 
connected the 

“Remote Level Control”

 port 

and used as a subwoofer level control).

B) Fade Front vs. Rear with no Subwoofer  

Level Control:

Req uired: 

a basic source unit or processor with 

two pairs of stereo outputs. 

Inp ut Connections: 

one pair of stereo source unit 

outputs is connected to the “

CH 1 (Left)

” and 

CH 2 (Right)

” inputs and the second pair  

of stereo source unit outputs is connected 
to the “

CH 3 (Left)

” and “

CH 4 (Right)

 

inputs of the M600/6 (select “

4 Ch.

” on the 

Input Mode

” switch in the “

Channel 5 & 6 

Controls

” section). 

Res ult: 

the relative level of the LF and HF 

channels will be fixed by the M600/6’s “

Input 

Sens.

” settings and will not be user adjustable 

from the helm, but the user will be able to fade 
the signal from front to rear.  
An optional HD-RLC can be connected the 

“Remote Level Control”

 port and used as a 

subwoofer level control, if desired.

C) Fade Subwoofer Level vs. HF Level:

Req uired: 

a basic source unit or processor with 

two pairs of stereo outputs. 

Inp ut Connections: 

the first stereo pair of source 

unit outputs each split with a “Y-Adaptor” 
allowing the left signal to be sent to the “

CH 

1 (Left)

” and “

CH 3 (Left)

” inputs and the 

right signal to be sent to the “

CH 2 (Right)

” 

and “

CH 4 (Right)

” inputs of the M600/6. 

The second stereo pair of source unit outputs 
is connected to the “

CH 5 (Left)

” and 

“CH 6 

(Right)

” inputs (select “

6 Ch.

” on the “

Input 

Mode

” switch). 

Res ult: 

in this mode, the user has the ability to 

fade or control the level of the LF channels 
relative to the HF channels via the source 
unit’s fader control without exceeding the 
maximum clean output level set by each 
amplifier section’s “

Input Sens.

” controls.

Summary of Contents for NexD M600/6












Reviews: