background image

11

1)  Left Channel Only or Right Channel Only 

Information:  If you wish to send a left-only 
or right-only signal to the M500/3’s main 
channels you must use a “Y-Adaptor” to split 

the single channel signal into both left and 

right RCA inputs of the bridged channel 

pair. This option is used when deploying the 
M500/3’s main channels to drive left channel 
speakers only or right channel speakers only.

2)  Left + Right Channel Information:  When 

bridged and fed by a stereo source signal, the 
M500/3’s main channels will automatically 
combine the left and right input signals into a 
summed mono (left + right) input signal. This 
can be useful to drive a center speaker.

SUBWOOFER OUTPUTS

The M500/3’s single subwoofer channel is 

designed to deliver power into subwoofer loads 
equal to or greater than 2 ohms. It is rated for 
300W into 2 ohms, 250W into 3 ohms and 200W 
into 4 ohms (Continuous Power, RMS Method).

IMPORTANT

!

 

Subwoofer loads below 2 ohms nominal are not 

recommended and may cause the amplifier  

to initiate a protection mode which reduces 

power output.

The M500/3’s subwoofer outputs are designed 

to accept 16 AWG - 8 AWG wire. To connect 
the subwoofer wires to the amplifier, first back 
out the set screws on the top of the terminal 
block, using the supplied 2.5 mm hex wrench. 
Strip 1/2 inch (12 mm) of insulation from the 
end of each wire and insert the bare wire into 
the terminal block, seating it firmly so that no 
bare wire is exposed. While holding the wire in 
place, tighten the set screw firmly, taking care 
not to strip the head of the screw and making 
sure that the wire (not the insulation) is firmly 
gripped by the wire clamp in the terminal.

 

INPUT SECTION

(L)

(R)

Remote

Level

Control

CH. 1&2

SUB CH.

Preouts

+12 VDC

Ground

Remote

CH. 1

(L)

CH. 2

(R)

Bridged

Mono Subwoofer Output

You will notice that there are two “+” positive 

connections and two “” negative connections. 
This is to facilitate multiple subwoofer wiring.  

The two positive and two negative connections 

are connected in parallel inside the amplifier 

They are not stereo outputs. Connecting two 
subwoofers, each to one set of positive and 
negative terminals, will result in a parallel 
subwoofer connection. If only connecting one 
pair of subwoofer wires, it is not necessary to use 
both sets of connections. 

Summary of Contents for M500/3





















Reviews: