background image

6

 

JL Audio

TURN-ON LEAD

The JX360/4 is turned on and off 

VTJOHBDPOWFOUJPOBM7SFNPUFUVSO

on lead, typically controlled by the 
source unit’s remote turn-on output. 

+12 VDC

Ground

Remote

5IFBNQMJGJFSXJMMUVSOPOXIFO7JT

present at its “

Remote

” input and turn off when 

7JTTXJUDIFEPGG*GBTPVSDFVOJUEPFTOPU

have a dedicated remote turn-on output, the 

BNQMJGJFSTUVSOPOMFBEDBOCFDPOOFDUFEUP7

via a switch that derives power from an ignition-
switched circuit. 

18 AWG wire is more than adequate for the 

remote turn-on connection. To connect the 
remote turn-on wire to the amplifier, strip 1/2-
inch (12 mm) of insulation from the wire and 
insert it into the “Remote” receptacle on the 
power connector. Tighten the connector down 
using the supplied 2.5 mm hex wrench.

INPUT SECTIONS

The JX360/4’s has two input sections: one for 

Channels 1&2 and another for Channels 3&4.
These input sections allows you to send signals to 
the amplifier sections through the use of either 
two or four inputs. Each input section offers 
two input connection methods, one for high-
level (speaker level) signals and one for low-level 
(preamp level) signals.

1)  Low-Level Inputs:

  A standard left/

right pair of RCA type jacks in the 

“Low-Level Inputs”

 section is used for 

preamp level (low-level) signal input 
on the JX360/4. This is the preferred 
connection method whenever available.

 

2)  Hi-Level Inputs: 

If your system does not offer 

a preamp level signal option, you can connect 
speaker level signals directly to the 

“Hi-Level 

Inputs”

 connectors using the supplied mating 

connectors and wire harnesses. Simply splice 
the appropriate left/right and positive/negative 
wires

 

to the included harnesses and plug the 

harness into the 

“Hi-Level Inputs”

 connectors 

on the amplifier. The JX360/4 will attenuate 
the high-level signals to make them compatible 
with its input stages.

 

Summary of Contents for JX360/4


















Reviews: