background image

12

 

JL Audio

 

 

 

 

13

aPPendix b:
J2-1000.1 specifications

 

general specifications:

Recommended Fuse Value:

  100A

Recommended Fuse Type:

 ANL at battery,  3x 35A ATC 

fuses on amplifier chassis.

input section:

Low-Level Input:

 Single-ended with RCA jacks

Low-Level Input Range:

 200mV - 6.5V RMS

High-Level Input: 

Single-ended with molded connector

High-Level Input Range: 

630mV - 20.5V RMS

amplifier section:

Amplifier Topology:

 Class D Monaural  

Power Supply: 

PWM switching type, unregulated

Rated Power with less than 1% THD (14.4V supply):

 

400W RMS x 1 @ 4Ω
500W RMS x 1 @ 3Ω
700W RMS x 1 @ 2Ω
900W RMS x 1 @ 1.5Ω
1000W RMS x 1 @ 1Ω

Frequency Response:

 10 - 160 Hz (+/– 0.5dB)

Crossover section:

Low-Pass Filter

: 12 dB/octave with continuously variable 

cutoff frequency selection from 40 - 300 Hz. Non-defeatable.

Preamp outputs:

2-Channel, pass-through with unity gain, RCA-type jacks.

bass boost

:

Single-band with 45 Hz center frequency, adjustable from  
0 to +12dB.

remote level Control

:

Via included, wired remote control knob. Full mute to  
0 dB range.

dimensions (lxwxH): 

14.60" x 9.60" x 2.15" (371 mm x 244 mm x 55 mm)

aPPendix a:
input sensitivity level setting

Following the directions below will allow the 

installer to adjust the input sensitivity of each 
amplifier channel pair simply and easily in just a 
few minutes using equipment which is commonly 
available in installation bays.

necessary equipment

• Digital AC Voltmeter
•  CD with a sine-wave test tone recorded at 

 

0 dB reference level in the frequency range  
to be amplified for that set of channels  
(50 Hz for subwoofer channels, 1 kHz for a 

midrange application). Do not use attenuated 

test tones (-10 dB, -20 dB, etc.).

the nine-step Procedure

 

1)

  Disconnect the speaker(s) from the 

 

amplifier’s speaker output connectors.

2)

  Turn off all processing (bass/treble, loudness, 

EQ, etc.) on the source unit, processors (if used) 
and amplifier. Set fader control to center position 
and subwoofer level control to 3/4 of maximum. 
If connected, set the amplifier’s Remote Bass 
Control at maximum (full clockwise).

3)

  Turn the 

“Input Sens.”

 control all the  

way down.

4)

  Set the source unit volume to 3/4 of full 

volume. This will allow for reasonable gain 
overlap with moderate clipping at full volume.

5)  

Using the chart on this page, determine the target 
voltage for input sensitivity adjustment according 
to the nominal impedance of the speaker system 
connected to the amplifier outputs.

6)

  Verify that you have disconnected the speakers 

before proceeding. Play a track with an 

appropriate sine wave (within the frequency 
range to be amplified) at 3/4 source unit volume.

7)

  Connect the AC voltmeter to the speaker output 

connectors of the amplifier. Make sure you test 

the voltage at the correct connectors (+ and –).

8)

  Increase the 

“Input Sens.”

 control until the 

target voltage is observed with the voltmeter.

9)

  Once you have adjusted the amplifier to 

its maximum low-distortion output level, 
reconnect the speaker(s). The 

“Input Sens.”

 

controls can now be adjusted downward if the 
amplifier requires attenuation to achieve the 
desired system balance. 

IMPORTANT

!

Do not increase any 

Input Sens.

 setting for 

any amplifier channel or channel pair in the 

system beyond the maximum level established 

during this procedure. Doing so will result in 

audible distortion and possible speaker damage.

It will be necessary to re-adjust the  

“Input Sens.”

 for the affected channels if any 

equalizer boost is activated after setting the  

“Input Sens.”

 with this procedure. This applies  

to any EQ boost circuit, including source unit 
tone controls or EQ circuits. EQ cuts will not 
require re-adjustment. 

 

nom. impedance

target aC Voltage

40 V

39 V

38 V

1.5Ω

37 V

32 V

Due to ongoing product development, all specifications are subject to 
change without notice.

Summary of Contents for J21000.1












Reviews: