background image

Page 19

 | 

CR-1

ACTIVE SUBWOOFER CROSSOVER

CR-1

Built in USA           

with domestic and imported components

OUTPUTS TO SATELLITE AMPLIFIER

MANAGED BASS INPUTS

L

R

L

R

RIGHT

LEFT

(OR MONO)

RIGHT

LEFT

OUTPUTS TO SUBWOOFER(S)

OUTPUTS TO

SUBWOOFER(S)

MANAGED BASS INPUTS

OUTPUTS TO

SATELLITE

AMPLIFIER

MAIN 

STEREO INPUTS

MAIN STEREO INPUTS

only feed subwoofer(s)

when crossover is bypassed.

FUSE

Replace fuse with proper

type and value only.

Refer to manual.

Warranty void if serial number is removed, altered or defaced.

CR-1 SERIAL NUMBER:

Grounded

Isolated

CR-1

This device complies with part 15 of the FCC rules. Operation is 

subject to the following two conditions: (1) this device may not cause 

harmful interference, and (2) this device must accept any interference 

received, including interference that may cause undesired operation.

BALANCED

BALANCED

BALANCED

BALANCED

BALANCED

BALANCED

BALANCED

BALANCED

Stereo

CAN ICES-3(B)/NMB-3(B) 

SOURCE INPUTS

MAIN OUTPUTS

SOURCE A

SOURCE B

SOURCE C

SOURCE D

SOURCE E

TAPE OUT

RIGHT

RIGHT

LEFT

LEFT

STEREO 

INPUTS

OUTPUTS TO LOUDSPEAKERS

BALANCED

BALANCED

LEFT 

BALANCED

RIGHT 

BALANCED

PREAMP OUTPUTS

FRONT

SURROUND

CENTER

SUB/LFE

SUBWOOFER/LFE OUTPUT

*

MAIN OUTPUTS

LEFT LOUDSPEAKER

RIGHT LOUDSPEAKER

DEDICATED HT LOUDSPEAKERS

OUTPUTS TO LOUDSPEAKERS

LEFT & RIGHT LOUDSPEAKERS IN 

2-CHANNEL MODE

(

”Crossover Function”

 switch in 

“On”

 Position)

FRONT LEFT & RIGHT SPEAKERS IN 

HOME THEATER MODE 

(

”Crossover Function”

 switch in 

“Bypass”

 Position)

CENTER

LEFT 

SURROUND

RIGHT 

SURROUND

Stereo Preamplifier

HT Receiver

CR-1

Stereo Amplifier

OR

Unbalanced

Balanced

LEFT POWERED 

SUBWOOFER

RIGHT POWERED

SUBWOOFER

OR

Unbalanced

Balanced

Balanced Connection

Unbalanced Connection

Stereo or Mono

WARNING!

 TURN OFF THE CR-1 AND ALL OTHER EQUIPMENT IN THE 

SYSTEM BEFORE MAKING OR CHANGING ANY CONNECTIONS! 

WARNING

Summary of Contents for CR-1





























Reviews: