background image

I N S T A L L A T I O N   G U I D E 

for the 

SB-P-996/13TW5v2 

SKU# 94537

1998-2004 Porsche 911 (996)   

Thank you for choosing a JL Audio Stealthbox® for your automotive sound system.  

With proper installation, your new vehicle-specific enclosed subwoofer system  

will deliver years of listening pleasure.

We strongly recommend that you have your new Stealthbox® installed by your authorized  

JL Audio dealer. The installation professionals employed by your dealer have the necessary tools 

and experience to disassemble and reassemble your vehicle properly.  If you prefer to perform your 

own installation, please read this installation guide completely before beginning the process.

  

If you choose to perform the installation yourself, it is absolutely vital that 

the Stealthbox

®

 be properly mounted to the vehicle according to these 

instructions.  Failure to mount the enclosure properly presents two problems:  
1) The sub-bass performance will suffer due to the movement of the enclosure 

caused by the force exerted by the woofer(s).
2) A loose enclosure presents a serious safety hazard in the event of a collision 

or sudden deceleration.

Continued on Next Page 

SB-P-996/13TW5v2  INSTR_SKU# 011334

INSTALLATION  

D I F F I C U L T Y :

5

5

OUT   

OF

ESTIMATED TIME:

         3-4 HOURS

S P E C I F I C A T I O N S

 

Enclosure Type: 

 Acoustic Suspension (sealed)

Driver Type:

  (2) 13TW5v2-4

Nominal Impedance:

  2 ohm

Continuous Power Handling:

  1200 watts

I N C L U D E D   H A R D W A R E

 

   

R E Q U I R E D   T O O L S

 

 

(2) 3/8 - 16 x 1-3/4” Hex Bolt          (1) Driver Enclosure Bracket
(6) 3/8” Split Lock Washer              (1) Pass Enclosure Bracket
(2) 3/8” x 1-1/4” Fender Washer     (2) 3/8 - 16 x 1-1/4” Hex Bolt
(4) 3/8” Flat Washer                        (2) 3/8” Hex Locknut
(2) 3/8” Nylon Washer                    (2) 3/8” Hex Nut
(2) Flat Bracket                                (2) Carpeted Panel
(2) U-Nut
(2) 3/8 - 16 x 2-1/4” Set Screw
(2) 3/8” x 1-1/2” Vinyl Cap
(2) Rear Bracket
(1) Driver Front Bracket
(1) Pass Front Bracket
(2) 1/4 - 20 x 1-1/2 Hex Drive Bolt

3/8 Drive Ratchet
3” Extension
8” Extension
12” Extension
3/8 Universal Joint
10mm Socket
15mm Deep Socket
Large Channel Lock Pliers
5/32 Allen Wrench

It is recommended to have a second person assist with the 
installation of this model.

Summary of Contents for 94537








Reviews: