manualshive.com logo in svg

JIMS MILWAUKEE-EIGHT 5833, Instruction Sheet

Share
Download
JIMS MILWAUKEE-EIGHT 5833 Instruction Sheet Download Page 10

CAUTION:   Wear safety glasses over your eye’s.

See JIMS

®

catalog for Hundreds of top quality professional tools.  

The last tools you will ever need to buy.

IIn

ns

st

tr

ru

uc

ct

tiio

on

n  S

Sh

he

ee

et

t  F

Fo

or

r  T

To

oo

ol

l  #

#5

58

83

33

3

Rev N/C 

7-19

No.5833-IS

1

10

0

555 Dawson Drive, Camarillo, CA 93012   Phone 805-482-6913 • Fax 805-482-7422

A Division of Thiessen Products, Inc.

15.

Align the Bearing Installer Pilot 

#5833-2

with the balancer bearing bore and carefully lower

the Bearing Installer Pilot by rotating the Screw 

#1024

clockwise until it bottoms out in the

balancer bearing bore, back off ¼ turn. DO NOT force the pilot into the bore or case dam-
age may result. Tighten the three 5/16-18 x 4” SHCS 

#5833-5

, 5/16” washers 

#1216

and

nuts 

#1222

until tight with an Allen key. 

See Fig. 7.

16. 

Back the Bearing Installer Pilot 

#5833-2

out by rotating counter clockwise, feeling for any

binding  between  the  balancer  bearing  bore  and  the  Bearing  Installer  Pilot.  If  binding  is
detected,  Loosen  the  three  5/16-18  x  4”  SHCS 

#5833-5

,  5/16”  washers 

#1216

and  nuts

#1222

and re insert the Bearing Installer Pilot 

#5833-2

and retighten the SHCS. Repeat until

there is no binding.

17.

Continue process - 

Fig 8. - Step 9.

FIG.11

Summary of Contents for MILWAUKEE-EIGHT 5833











Reviews:

No comments

Brands by name

Popular brands

Load more brands