background image

The battery features a thermal fuse with a rest fuse that will automatically trip and cut all 
power to the vehicle if the motor, electric system or battery is overloaded. The fuse will 
reset and power will be restored after the unit is turned OFF for 20 seconds and then turned 
ON again. If the thermal fuse trips repeatedly during normal use, the vehicle may need 
repair. 

Contact your distributor please.

To avoid losing power, follow these guidelines:

● Do not overload the vehicle.

● Do not tow anything behind the vehicle.

● Do not drive up steep slopes.

● Do not drive into fixed objects, which may cause the wheels to spin, causing the motor to  

overheat.

● Do not drive in very hot weather, components may overheat.

● Do not allow water or other liquids to come in contact with the battery or other electric 

components.

● Do not tamper with the electric system. Doing so may create a short, causing the fuse to 

trip.

•  

It is parents' responsibility to check main parts of the toy before using, Must 

regularly examine for potential hazard, such as the battery, charge, cable or 

cord, plug, screws are fastening enclosure of other parts and that in the event 

of such damage, the toy must not be used until that damage had been properly 

removed. 

•  Park the vehicle indoors or cover it with a tarp to protect it from wet weather. 
•  Recharge the battery after each use. Only an adult can handle the battery. 

Recharge the battery at least once a month when the vehicle raider is not being 

used. 

•  Do not wash the vehicle with a hose. Do not wash the vehicle with soap and 

water. Do not drive the vehicle in rainy or snowy weather. Water will damage 

the motor, electric system and battery. 

•  Clean the vehicle with a soft, dry cloth. To restore shine to plastic parts, use a 

non-wax furniture polish. Do not use car wax. Do not use abrasive cleaners.

•  When not using, all the electrical source should be turn off. Turn off the power 

switch and disconnect the battery connection.

Our products are suitable for 

ASTM F963; GB6675; EN71 and EN62115 standard.

Fuse 

Maintaining    │  15

Summary of Contents for AUDI Q8

















Reviews: