manualshive.com logo in svg

JETWAY NF792I Series, User Manual, Page: 47 / 48

Share
Download
JETWAY NF792I Series User Manual Download Page 47

 
 
 

 

                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                               

 
 
 

 

42 

UEFI Boot 
The optional settings are: [Disabled]; [Enabled]; [Auto]. 
[Auto]: If the 1

st

 boot HDD is GPT then enable UEFI boot options, otherwise disable. 

[Enabled]: Enable all UEFI boot options. 
[Enabled]: Disable all UEFI boot options. 

3-11 Save & Exit Menu 

 

Save Changes and Reset 
This item allows user to reset the system after saving the changes. 
Discard Changes and Reset 
This item allows user to reset the system without saving any changes. 
Restore Defaults 
Use this item to restore /load default values for all the setup options. 
Save as User Defaults 
Use this item to save the changes done so far as user defaults. 

Summary of Contents for NF792I Series

















































Reviews:

No comments