manualshive.com logo in svg

JETWAY JNC9NDL-2550, Technical Manual, Page: 36 / 41

Share
Download
JETWAY JNC9NDL-2550 Technical Manual Download Page 36

 

31

►

 

Voltage Configuration 

DIMM Voltage 

The optional settings are: [Default]; [+50mV]; [+100mV]; [+150mV]. 

►

 

Watchdog Configuration 

WatchDog Timer Control 

Use this item to enable or disable WatchDog Timer Control. When set as 

[Enabled], the following sub-items shall appear: 

WatchDog Timer Val 

User can set a value in the range of 4 to 255. 

WatchDog Timer Unit 

The optional settings are: [Second];[Minute]. 

►

 

Shutdown Temperature Configuration 

Use this item to select system shutdown temperature. 

►

 

SmartFan Configuration 

CPUFAN1 / SYSFAN1/SYSFAN2 SmartFan Mode 

When set as [Enabled], the following sub-items shall appear:   

CPUFAN1/ SYSFAN1/SYSFAN2 Full Speed Temp 

Use this item to set a degree for CPU/SYSFAN1/ SYSFAN2 to run at full speed 

when above the specific temperature set. 

CPUFAN1 / SYSFAN1/SYSFAN2 Idle Temp   

Use this item to set a degree for CPU/SYSFAN1/ SYSFAN2. FAN will idle speed 

when below this temperature. 

CPUFAN1 / SYSFAN1/SYSFAN2 Stop Temp   

Use this item to set a degree for CPU/SYSFAN1/ SYSFAN2. CPU FAN will stop 

when below this temperature. 

 

Summary of Contents for JNC9NDL-2550










































Reviews:

No comments