background image

 

35

WatchDog Timer Value 

User can set a value in the range of 4 ~255. 

WatchDog Timer Unit 

The optional settings are: [Min.]; [Sec.]. 

ATX Power Emulate AT Power 

This item will show current AT Mode is enabled or disabled. 

*Note

: User needs to reset the system for the settings to take effect after setting 

Pin 1-2 of AT_MODE jumper as closed. 

Case Open Detect 

Use this item to detect case has already open or not, show message in POST. 
The optional settings are: [Disabled]; [Enabled]. 

 

PC Health Status 

Press [Enter] to view current PC health status and make settings for: 

Shutdown Temperature   

Use this item to select system shutdown temperature.   
The optional settings are: [Disabled]; [70C/158F]; [75C/164F] [80C/172F]; 
[85C/180F]; [90C/188F]. 

 

SmartFAN Configuration 

Press [Enter] to make settings for SmartFan Configuration: 

SmartFAN Configuration 

CPUFAN Type 

The optional settings are: [4 pin]; [3 pin]. 

SYSFAN1 Type   

The optional settings are: [4 pin]; [3 pin]. 

SYSFAN2 Type   

SYSFAN2 only support [4 pin] type. 

*Note:

 ‘

Smart Mode

’ is not supported when the [3 pin] type is selected. 

CPUFAN / SYSFAN1/SYSFAN2 Smart Mode 

When set as [Enabled], the following sub-items shall appear:   

CPUFAN / SYSFAN1/SYSFAN2 Full-Speed Temperature

   

Use this item to set CPUFAN/SYSFAN1/SYSFAN2 full speed temperature. Fan 
will run at full speed when above this temperature. 

Summary of Contents for G03-NC9T-F


















































Reviews: