JETWAY FFI02 Series Quick Installation Manual Download Page 8 | Manualshive

Page: 8 / 20

background image

8

*Note:

There should be one more

HCS310HS1-F / HCS3XXHS2-F / HCSHBFFHS1-1F

left as spare parts

after normal assembly. User can use them to replace corresponding damaged thermal conductive pads.

Notice

：

Please restore the screws that lock the motherboard to the chassis cover when CPU & heatsink

installation completed. The cables unplugged during this process should be plugged to their original places

after heatsink installation.

IV. To Install SO-DIMM to the board

1.

Find the SO-DIMM slot on the board.

«
...
6
7
8
9
10
...
»

Summary of Contents for FFI02 Series





















Reviews:

No comments

Related manuals for FFI02 Series

Brand: Panasonic Pages: 4

Brand: Paradox Pages: 4

Brand: Zenith Data Systems Pages: 64

ILDA Gem Laser projector tool

Brand: Stanwax Laser Pages: 3

Brand: Lorex Pages: 186

Brand: RAK Pages: 30

Brand: Lanner electronics Pages: 59

Super Sound Set SR-JV80-07

Brand: Roland Pages: 8

Brand: Schrack Technik Pages: 2

iCE40 SPRAM Series

Brand: Lattice Semiconductor Pages: 12

IPS Pro-Module-24C-GE-BP-TM

Brand: Trend Micro Pages: 3

Brand: AMD Pages: 27

Brand: EXAGATE Pages: 7

Brand: Linksys Pages: 17

F2MC-16L Series

Brand: Fujitsu Pages: 68

Brand: ANTUMBRA Pages: 11

Brand: Swann Pages: 30

Brand: Verizon Wireless Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands