background image

Welcome!

  Congratulations on the purchase of your new Jets Munt VT80 gas turbine engine. Jets Munt
are dedicated to the design and production of engines to the highest standards of quality
and reliability to bring you the customer the very latest next generation engine designs.
  The VT80 is the result of an intensive effort of design and tests by the Jets-Munt staff.
During the development period we made extensive use of the latest Computational Flow
Dynamics programs allowing us to optimise the engine performance characteristics.

PLEASE READ!

  The Jets Munt SL responsibility is limited exclusively to the repair of the engine and
accessories which are outlined in the conditions of warranty.
Before unpacking the engine please read the manual, and agree to the conditions of
warranty.

  Customer satisfaction is important to Jets Munt SL. Technical support is available trough
your local dealer and trough email.

Jets Munt S.L

Torrent d’en Puig 31

08358 Arenys de Munt

Barcelona. Spain

Web site: www.jets-munt.com

E-mail: [email protected]

Fax: +34 93 7950113

Legal and Disclaimer

  The engine design and the contents of this manual are copyright by Jets Munt SL, Arenys
de Munt, Barcelona, Spain. All rights reserved.
This manual, the pictures and data are property of Jets-Munt and cannot be used or
reproduced in any way without written permission from Jets Munt SL.

Disclaimer

  The VT80BL engine is a sophisticated piece of machinery. Care should be taken at all times
when using the engine. It should only be operated by those with the appropriate skills and
knowledge to do so. This engine is not a toy. Incorrect operation or misuse can cause 
damage to property and bodily harm operators, spectators and animals. Jets Munt SL 
accepts no liability for any kind of damage which may occur.
  Jets Munt SL assumes no responsibility for any errors contained in this document and is not
liable for any damages resulting from such errors. 

It is forbidden the use of this engine outside Radio Control applications,

specially those that power vehicles that carry people.

JETS MUNT S.L

VT80BL Instruction Manual 

Page 3

Summary of Contents for VT80BL
























Reviews: