background image

 

31

Parts List: Upper Wheel Assembly 

Index No.  Part No. 

Description 

Size 

Qty 

1 ..........VBS18MW-101.................Saw Body..................................................................................... 1 
2 ..........TS-0152011 .....................Carriage Bolt ................................................5/16-18x1 ................. 6 
3 ..........JWBS18DX-103  ...............Upper Wheel Bracket (Right Side) ................................................. 1 
4 ..........TS-0680031 .....................Flat Washer..................................................5/16 ......................... 6 
5 ..........TS-0720081 .....................Lock  Washer ................................................5/16 ......................... 6 
6 ..........TS-0561021 .....................Hex Nut........................................................5/16-18 .................... 6 
7 ..........JWBS18-107 ....................Switch .......................................................................................... 1 
8 ..........TS-1490151 .....................Hex Cap Screw ............................................M8x80...................... 1 
9 ..........TS-0680021 .....................Flat Washer..................................................1/4 ........................... 4 
10 ........JWBS18DX-110  ...............Sliding  Bracket  ............................................................................. 1 
11 ........VBS18MW-111.................Blade Tension Indicator................................................................. 2 
13 ........JWBS18DX-113  ...............Shaft  Bracket................................................................................ 1 
14 ........TS-1540061 .....................Hex Nut........................................................M8 ........................... 1 
15 ........JWBS18-115 ....................Spring .......................................................................................... 1 
16 ........JWBS18-116 ....................Square  Nut ................................................................................... 1 
17 ........JWBS18DX-117  ...............Pointer ......................................................................................... 1 
18 ........JWBS18-118 ....................Screw  ..........................................................M5x8  ....................... 1 
21 ........JWBS18DX-121 ...............Bracket ........................................................................................ 1 
22 ........TS-0050021 .....................Hex Cap Screw ............................................1/4-20x5/8 ................ 4 
23 ........JWBS18DX-123  ...............Blade Adjusting Screw .................................................................. 1 
24 ........JWBS18-124 ....................E-Ring  .........................................................E-9  .......................... 1 
25 ........JWBS18-125 ....................Hand  Wheel  ................................................................................. 1 
26 ........TS-0267041 .....................Set  Screw  ....................................................1/4-20x3/8 ................ 2 
27 ........TS-0209021 .....................Socket Head Cap Screw ...............................3/8-16x5/8 ................ 1 
28 ........TS-0720091 .....................Lock Washer  ...............................................3/8 ........................... 1 
29 ........JWBS18-129 ....................Upper Wheel Shaft ....................................................................... 1 
30 ........BB-6203ZZ.......................Ball Bearing..................................................6203ZZ .................... 2 
31 ........JWBS18-131 ....................Retaining  Ring ..............................................R40  ......................... 2 
32 ........JWBS18-132 ....................Upper Wheel ................................................................................ 1 
33 ........JWBS18DX-133  ...............Tire .............................................................................................. 1 
34 ........JWBS18-134 ....................Flat  Washer.................................................................................. 1 
35 ........JWBS18-135 ....................Hex  Nut........................................................5/8-18UNF  L.H.  ........ 1 
36 ................................................Blade 

(local purchase)

 ..................................137” ......................... 1 

37 ........TS-0590061 .....................Wing Nut ......................................................5/16-18 .................... 1 
38 ........JWBS18-138 ....................Lock  Knob ....................................................5/16 ......................... 1 
39 ........JWBS18DX-139  ...............Upper Front Door.......................................................................... 1 
40 ........JWBS18-140 ....................JET  Nameplate............................................................................. 1 
41 ........JWBS18-141 ....................Warning  Label .............................................................................. 1 
42 ........JWBS18-142 ....................Bolt .............................................................................................. 1 
43 ........TS-0561011 .....................Hex Nut........................................................1/4-20 ...................... 1 
44 ........TS-081C052 .....................Screw ..........................................................#10-24x3/4 ............... 2 
45 ........JWBS18-39A....................Door Hinge Pin ............................................................................. 2 
46 ........JWBS18DX-146  ...............Upper Wheel Bracket (Left Side).................................................... 1 
47 ........JWBS18DX-147  ...............Tracking  Window .......................................................................... 1 
48 ........TS-081C032 .....................Screw ..........................................................#10-24x1/2 ............... 2 
49 ........TS-1550031 .....................Flat Washer..................................................M5 ........................... 2 
50 ........TS-2361051 .....................Lock Washer ................................................M5 ........................... 2 
51 ........TS-0560071 .....................Hex Nut........................................................#10-24 ..................... 2 
53 ........JWBS18DX-153  ...............Scale  Bracket ............................................................................... 1 
54 ........TS-081C022 .....................Screw ..........................................................#10-24x3/8 ............... 2 

 

 

 

Summary of Contents for VBS-18MW









































Reviews: