background image

 

14 

10.  Replace  and  reset  the  other  three  knives  in 

the same manner. 

11.  After  all  four  knives  are  set  with  the  screws 

just snug, back out and tighten the six screws 
(F)  against  the  slot  starting  with  the  end 
screws  first  and  then  the  center  screws  until 
the  knife  is  securely  held  in  the  cutterhead. 
Tighten  the  remaining  three  knives  in  the 
same manner. 

  After  replacing  and  checking 

knives,  CHECK  AGAIN  carefully.  Make  certain 
the  direction  of  knives  is  correct  and  all 
twenty-four  locking  screws  are  tightened 
securely. 

Replacing or Rotating Knife Inserts 

(Model JWP-208HH only) 

The  knife  inserts  on  the  model  JWP-208HH  are 
four-sided. When dull, simply remove each insert, 
rotate it 90° for a fresh edge, and re-install it. 

Use the provided star point screwdriver to remove 
the  knife  insert  screw.  See  Figure  20a.  It  is 
advisable to rotate all inserts at the same time to 
maintain  consistent  cutting.  However,  if  one  or 
more  knife  inserts  develops  a  nick,  rotate  only 
those inserts that are affected. 

Each knife insert has an etched reference mark so 
you can keep track of the rotations. 

IMPORTANT:

 When removing or rotating inserts, 

clean saw dust from the screw, the insert, and the 
cutterhead  platform.  Dust  accumulation  between 
these  elements  can  prevent  the  insert  from 
seating properly, and may affect the quality of the 
cut. 

Before installing each screw, lightly coat the screw 
threads with machine oil and wipe off any excess. 

Securely tighten each screw which holds the knife 
inserts before operating the planer! 

 

Make  sure  all  knife  insert 

screws  are  tightened  securely.  Loose  inserts 
can be propelled at high speed from a rotating 
cutterhead, causing injury.

 

 

Checking Work Table Parallel to 

Cutterhead 

The work table is set parallel to the cutterhead at 
the  factory  and  no  further  adjustment  should  be 
necessary. If your machine is planing a taper, first 
check  to  see  if  the  knives  are  set  properly  in  the 
cutterhead. Then check to see if the work table is 
set parallel to the cutterhead. Proceed as follows: 

 

 

 

 

 

 

 

 

 

 

 

 

 

Figure 20a – JWP-208HH only 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for JWP-208HH





































Reviews: