manualshive.com logo in svg

Jet JWP-12DX, Owner'S Manual

Share
Download
Jet JWP-12DX Owner'S Manual Download Page 14

14

Feed Roller Maintenance

The feed rollers are made of a rubber material
and should be inspected after every hour of
operation:

1.

Unplug the machine from the power
source.

2.

Move the cutterhead to the top of the
planer.

3.

Inspect both the infeed and the outfeed
rollers for sawdust and wood chips. Rotate
the rollers by turning the cutterhead belt.
Due to the gear reduction on the rollers the
cutterhead must be rotated a significant
amount.

You can remove the right side

panel to make the rotating of the cutterhead
belt easier.

4.

To remove sawdust or wood chips, first use
a soft brush. If chips or dust remain, use a
soft cloth with a mild cleaner. Do not touch
the rollers with sharp or abrasive objects.

Lubrication

WARNING

Unplug the planer from the power source

before attempting any lubrication!

Failure to comply may cause serious injury!

To access the following lubrication points,
remove the elevating hand wheel assembly and
the top and side cover assembly.

• 

Leadscrews - (B, Fig. 18) Apply a light coat
of #2 lithium tube grease along the entire
length of both leadscrews.

• 

Columns - (C, Fig. 18) Apply a light coat of
#2 lithium tube grease to all four columns,
upon which the cutterhead slides up and
down. Wipe away excess grease.

• 

Feed Rollers - Carefully place the planer on
its side and apply a drop of 30W machine
tool oil to each of the four feed roller
brackets

(#33

in

the

head

assembly

breakdown). Wipe away any excess.

• 

Drive Chain - Apply a light coat of 30W
machine tool oil to the drive chain.

Keep

the chain clean of dust, dirt, and wood
shavings.

Do not over lubricate.

Over

lubricating

the

chain

will

attract

contaminates and increase the wear on the
chain.

To access the following lubrication points,
carefully turn the planer over on its side.

• 

Beveled Gears - Apply a small dab of #2
lithium tube grease between the gears (#3
and #29 in the table assembly breakdown)
on both the left and right side of the planer.
Turn the height handle a few time to spread
the grease and wipe off any excess.

Summary of Contents for JWP-12DX
























Reviews:

No comments

Brands by name

Popular brands

Load more brands