Jet JJP-12 Operating Instructions And Parts Manual Download Page 16

Page: 16 / 40

Belt Replacement

Disconnect machine from

power source before making any adjustments.
Failure to comply may cause serious injury.

Preparation

To replace the

cutterhead drive belt

and/or the

planer feed-roller belt

, the jointer fence assembly

and two back panels must first be removed as
described below. A 4mm hex wrench and two
13mm wrenches are required.

1. Remove

the

jointer fence assembly

(A) by first

loosening and removing two l

ock handle

assemblies

(B). A 4mm hex wrench is helpful,

but not necessary.

2. Remove two

button head socket scre

ws (C)

and

upper back panel

(D).

3. Remove four

button head socket scre

ws (O)

and

lower back panel

(P).

Cutterhead Drive Belt Replacement

4. Loosen four

motor mount screws

(L). Lift the

motor and rest it in the horizontal slot side of
the motor mount opening. This will create a
slack in the

cutterhead drive

belt

(F).

5. Remove the

cutterhead drive belt

(F) from

around the

cutterhead pulley

(E) and

motor

pulley

(M).

6. If the

feed-roller belt

(K) is to be replaced,

continue. Otherwise proceed to step 10.

Feed-roller Belt Replacement

Note:

If the feed-roller belt is to be replaced, steps

1–5 must be performed to remove the cutterhead
drive belt before the feed-roller belt can be
replaced.

7. Place the

power feed handle

(J) in the

down

(off/disengaged) position, which provides belt
slack for the next step.

8. Remove the

feed-roller belt

(G) from around

the

feed-roller pulley

(K) and

motor pulley

(M).

9. Loop the new belt around the smaller (inner)

motor pulley

(M) and

feed-roller pulley

(K).

Note:

The lower stretch of the feed-roller

pulley must be positioned between the

belt-

brake plates

(N).

Concluding Steps

10. Replace the

cutterhead drive belt

(F) by

looping it around the

cutterhead pulley

(E),

then the larger (outside)

motor pulley

(M).

11. Slide the motor so the

mounting screws

(L)

rest back in the vertical slot openings, then

Figure 13

tighten the mounting screws.

12. Replace the

lower back panel

(P) and secure

with four

button head socket scre

ws (O).

13. Replace the

upper back panel

(D) and secure

with two

button head socket scre

ws (C).

14. Replace the

jointer fence assembly

(A) and

secure with two

lock handle assemblies

(B).

Summary of Contents for JJP-12









































Search results

Summary of Contents for JJP-12

Reviews:

Related manuals for JJP-12

Brands by name

Popular brands

Jet JJP-12, Operating Instructions And Parts Manual

Search results

Summary of Contents for JJP-12

Reviews:

Related manuals for JJP-12

Brands by name

Popular brands