Jet JJ-8CS Owner'S Manual Download Page 2

2

Warranty & Service

The JET Group warrants every product it sells.  If one of our tools needs service or repair, one of our Authorized
Repair Stations located throughout the United States can give you quick service.

In most cases, any one of these JET Group Repair Stations can authorize warranty repair, assist you in
obtaining parts, or perform routine maintenance and major repair on your JET, Performax or Powermatic tools.

For the name of an Authorized Repair Station in your area, please call 1-800-274-6848.

More Information

Remember, the JET Group is consistently adding new products to the line.  For complete, up-to-date product
information, check with your local JET Group distributor.

JET Group Warranty

The JET Group (including Performax and Powermatic brands) makes every effort to assure that its products
meet high quality and durability standards and warrants to the original retail consumer/purchaser of our
products that each product be free from defects in materials and workmanship as follow:  1 YEAR LIMITED
WARRANTY ON ALL PRODUCTS UNLESS SPECIFIED OTHERWISE.  This Warranty does not apply to
defects due directly or indirectly to misuse, abuse, negligence or accidents, normal wear-and-tear, repair or
alterations outside our facilities, or to a lack of maintenance.

THE JET GROUP LIMITS ALL IMPLIED WARRANTIES TO THE PERIOD SPECIFIED ABOVE, FROM THE
DATE THE PRODUCT WAS PURCHASED AT RETAIL. EXCEPT AS STATED HEREIN, ANY IMPLIED WAR-
RANTIES OR MERCHANTIBILITY AND FITNESS ARE EXCLUDED. SOME STATES DO NOT
ALLOW LIMITATIONS ON HOW LONG THE IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION
MAY NOT APPLY TO YOU. THE JET GROUP SHALL IN NO EVENT BE LIABLE FOR DEATH, INJURIES TO
PERSONS OR PROPERTY, OR FOR INCIDENTAL, CONTINGENT, SPECIAL, OR CONSEQUENTIAL DAM-
AGES ARISING FROM THE USE OF OUR PRODUCTS. SOME STATES DO NOT ALLOW THE EXCLUSION
OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR
EXCLUSION MAY NOT APPLY TO YOU.

To take advantage of this warranty, the product or part must be returned for examination, postage prepaid, to
an Authorized Repair Station designated by our office.  Proof of purchase date and an explanation of the
complaint must accompany the merchandise.  If our inspection discloses a defect, we will either repair or
replace the product, or refund the purchase price if we cannot readily and quickly provide a repair or replace-
ment, if you are willing to accept a refund.  We will return repaired product or replacement at JET’s expense,
but if it is determined there is no defect, or that the defect resulted from causes not within the scope of JET’s
warranty, then the user must bear the cost of storing and returning the product.  This warranty gives you
specific legal rights; you may also have other rights which vary from state to state.

The JET Group sells through distributors only.  Members of the JET Group reserve the right to effect at any
time, without prior notice, those alterations to parts, fittings, and accessory equipment which they may deem
necessary for any reason whatsoever.

This manual has been prepared for the owner and operators of a JET JJ-8CS.  Its purpose, aside
from machine operation, is to promote safety through the use of accepted correct operating and
maintenance procedures.  Completely read the safety and maintenance instructions before operat-
ing or servicing the machine.  To obtain maximum life and efficiency from your jointer, and to aid in
using the machine safely, read this manual thoroughly and follow all instructions carefully.

Summary of Contents for JJ-8CS





























Reviews: