background image

 

2

This manual has been prepared for the owner and operators of a JDP-15M/MF Drill Press.  Its purpose, 
aside from machine operation, is to promote safety through the use of accepted correct operating and 
maintenance procedures.  Completely read the safety and maintenance instructions before operating or 
servicing the machine.  To obtain maximum life and efficiency from your JET Drill Press, and to aid in 
using the machine safely, read this manual thoroughly and follow instructions carefully. 

Warranty 

The WMH Tool Group warrants every product it sells.  If one of our tools needs service or repair, one of 
our Authorized Repair Stations located throughout the United States can give you quick service. 

In most cases, any one of these WMH Tool Group Repair Stations can authorize warranty repair, assist 
you in obtaining parts, or perform routine maintenance and major repair on your JET, Performax, Wilton, 
or Powermatic tools. 

For the name of an Authorized Repair Station in your area, please call 1-800-274-6848, or visit 
www.wmhtoolgroup.com 

More Information 

Remember, the WMH Tool Group is consistently adding new products to the line.  For complete, up-to-
date product information, check with your local WMH Tool Group distributor, or visit 
www.wmhtoolgroup.com 

WMH Tool Group Warranty 

The WMH Tool Group (including Performax, Wilton and Powermatic brands) makes every effort to assure 
that its products meet high quality and durability standards and warrants to the original retail 
consumer/purchaser of our products that each product be free from defects in materials and workmanship 
as follow:  1 YEAR LIMITED WARRANTY ON ALL PRODUCTS UNLESS SPECIFIED OTHERWISE.  
This Warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence or 
accidents, normal wear-and-tear, repair or alterations outside our facilities, or to a lack of maintenance. 

THE WMH TOOL GROUP LIMITS ALL IMPLIED WARRANTIES TO THE PERIOD SPECIFIED ABOVE, 
FROM THE DATE THE PRODUCT WAS PURCHASED AT RETAIL.  EXCEPT AS STATED HEREIN, 
ANY IMPLIED WARRANTIES OR MERCHANTIBILITY AND FITNESS ARE EXCLUDED.  SOME 
STATES DO NOT ALLOW LIMITATIONS ON HOW LONG THE IMPLIED WARRANTY LASTS, SO THE 
ABOVE LIMITATION MAY NOT APPLY TO YOU.  THE WMH TOOL GROUP SHALL IN NO EVENT BE 
LIABLE FOR DEATH, INJURIES TO PERSONS OR PROPERTY, OR FOR INCIDENTAL, 
CONTINGENT, SPECIAL, OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OF OUR 
PRODUCTS.  SOME STATES DO NOT ALLOW THE EXLUSION OR LIMITATION OF INCIDENTAL OR 
CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO 
YOU. 

To take advantage of this warranty, the product or part must be returned for examination, postage 
prepaid, to an Authorized Repair Station designated by our office.  Proof of purchase date and an 
explanation of the complaint must accompany the merchandise.  If our inspection discloses a defect, we 
will either repair or replace the product, or refund the purchase price if we cannot readily and quickly 
provide a repair or replacement, if you are willing to accept a refund.  We will return repaired product or 
replacement at WMH Tool Group’s expense, but if it is determined there is no defect, or that the defect 
resulted from causes not within the scope of WMH Tool Group’s warranty, then the user must bear the 
cost of storing and returning the product.  This warranty gives you specific legal rights; you may also have 
other rights, which vary from state to state. 

The WMH Tool Group sells through distributors only.  Members of the WMH Tool Group reserve the right 
to effect at any time, without prior notice, those alterations to parts, fittings, and accessory equipment, 
which they may deem necessary for any reason whatsoever. 

Summary of Contents for JDP-15M

























Reviews: