background image

 

5.0

  Electrical connections 

 

All electrical connections 

must be done by a qualified electrician in 
compliance with all relevant codes and 
ordinances. Failure to comply may result in 
serious injury.

 

The JDC-510 Dust Collector is rated at 230 volt, 
single phase only, and is provided with a 6-20P 
plug designed for use on a circuit with a 
grounded outlet that looks like the one pictured 
in Figure 5-1. 

Before connecting to power source, be sure 
switch is in off position.  

It is recommended that the JDC-510 be 
connected to a dedicated minimum 20 amp 
circuit with circuit breaker or time-delay fuse 
marked “D”. 

Local codes take precedence 

over recommendations.

 

5.1

  GROUNDING INSTRUCTIONS 

1. All Grounded, Cord-connected Tools: 

In the event of a malfunction or breakdown, 
grounding provides a path of least resistance for 
electric current to reduce the risk of electric 
shock. This tool is equipped with an electric cord 
having an equipment-grounding conductor and a 
grounding plug. The plug must be plugged into a 
matching outlet that is properly installed and 
grounded in accordance with all local codes and 
ordinances. 

Do not modify the plug provided - if it will not fit 
the outlet, have the proper outlet installed by a 
qualified electrician. 

Improper connection of the equipment-
grounding conductor can result in a risk of 
electric shock. The conductor with insulation 
having an outer surface that is green with or 
without yellow stripes is the equipment-
grounding conductor. If repair or replacement of 
the electric cord or plug is necessary, do not 
connect the equipment-grounding conductor to a 
live terminal. 

 

Check with a qualified 

electrician or service pe

r

sonnel if the 

grounding instructions are not completely 
understood, or if in doubt as to whether the 
tool is properly grounded. Failure to comply 
may cause serious or fatal injury.

 

Use only 3-wire extension cords that have 3-
prong grounding plugs and 3-pole receptacles 
that accept the tool's plug. 

Repair or replace damaged or worn cord 
immediately. 

2. Grounded, cord-connected tools intended for 
use on a supply circuit having a nominal rating 
between 

150 - 250 volts

, inclusive: 

This tool is intended for use on a circuit that has 
an outlet that looks like the one illustrated in 

D,

 

Figure 5-1. The tool has a grounding plug that 
looks like the plug illustrated in 

D

. Make sure the 

tool is connected to an outlet having the same 
configuration as the plug. No adapter is 
available or should be used with this tool. If the 
tool must be reconnected for use on a different 
type of electric circuit, the reconnection should 
be made by qualified service personnel; and 
after reconnection, the tool should comply with 
all local codes and ordinances. 

 

Figure 5-1 

5.2

  Extension cords 

The use of extension cords is discouraged; try to 
position equipment within reach of the power 
receptacle. If an extension cord becomes 
necessary, be sure it is heavy enough to carry 
the current your product will draw. An 
undersized cord will cause a drop in line voltage 
resulting in loss of power and overheating.  

Table 2 shows recommended size to use 
depending on cord length and nameplate 
ampere rating. If in doubt, use the next heavier 
gauge. The smaller the gauge number, the 
heavier the cord. 

Amp Rating 

Volts  Total length of cord in feet 

More 
Than 

Not 
More 
Than 

240 50 100 200  300 

 AWG 

0 6 

  18 

16 

16 14 

6 10 

  18 

16 

14  12 

10 12 

  16 

16 14  12 

12 16 

  14 

12 

Not 
Recommended 

 

Extension Cord Recommendations 

Table 2 

Summary of Contents for JDC-510













Reviews: