Jet JAT-900 Operations & Parts Manual Download Page 7

JET   

 

Setup and Assembly 

Any missing parts or damage should be reported 
immediately to your JET

®

 distributor. Do not use a 

damaged tool. Read this instruction manual 
thoroughly for operation, maintenance and safety 
instructions. 

Box contents: 

1 Pneumatic 

hammer 

1 Spring 

retainer 

4 Chisels 

Operation and parts manual  

1 Warranty 

card 

Operation 

 

The air hammer must be 

properly lubricated before operation. See 
“Lubrication” section. 

 

Figure 1 

1.  Insert chisel shank into cylinder of air 

hammer. Slide spring retainer over chisel 
and screw it all the way onto cylinder; use 
rear tab for leverage. Make sure front coil of 
spring surrounds chisel (inset, Figure 1). 

2. 

Pull on chisel to verify it is secure. 

3. 

Remove protective cap from air inlet (Figure 
1). If an in-line oiler is not being used, add 4 
or 5 drops of air tool oil (not included) into the 
air inlet. 

4.  Blow out air line to remove any dirt or 

moisture, then connect air supply hose to 
tool. Set air pressure to 90 psi. 

IMPORTANT:

 Connecting a quick-change 

coupling directly to the tool is not 
recommended, as vibration may cause the 
connection to fail. Instead, add a leader hose 
and install any quick-change couplings 
farther down the line. 

5. 

Adjust speed with air regulator knob.  

6. 

Hold air hammer with both hands, and press 
chisel blade against target surface. Press 
trigger to begin hammering action. 

7. 

Release trigger to stop air hammer. 

Four chisels are provided with the air hammer 
(Figure 2). 

 

Figure 2 (p/n JSG-1304) 

A. Flat chisel 
B. Nut splitter 
C. Tapered punch 
D. Panel cutter 

Maintenance 

Lubrication 

The air hammer should be lubricated daily (or 
before each use) with air tool oil through the air 
inlet. During continual operation, it should be re-
oiled every 1 to 2 hours. This can be done with an 
in-line oiler, or manually. If done manually, 
proceed as follows: 

1. 

Disconnect air hose from tool. 

2. 

Place 4 or 5 drops of air tool oil into air inlet 
(Figure 1). 

NOTE: Air tool oil not provided; it is available 
at most major hardware and tool stores. SAE 
#10 oil or sewing machine oil may be used 
as a substitute. Do not use detergent oil. 

Summary of Contents for JAT-900

















Reviews: