Jet J-4210 Operating Instructions And Parts Manual Download Page 6

 6

6.0

  Specifications  

Model number 

J-4210 

Stock numbers 

Belt/Disc Sander with Stand 

414550K 

Belt/Disc Sander only 

414550 

Stand only 

414549 

Motor and Electricals 

Motor type 

Totally enclosed, fan cooled 

Horsepower 1 

HP 

Motor phase 

single 

Motor voltage 

115/230 V 

Cycle 

60 Hz 

Full load amperage (FLA) 

10 / 5.5 

Motor speed 

3450 RPM 

Power transfer 

v-belt 

On/off switch 

Pushbutton with removable safety key 

Recommended circuit size 

1

 15 

Belt sanding 

Belt speed 

1650 SFPM 

Belt size and grit 

6 x 48 in. (153 x 1219 mm), 80 Grit 

Dust port, outside diameter 

2-1/2 in. (63.5 mm) 

Platen 

Cast iron 

Belt table 

Cast iron, 6 x 10-1/2 in. (153 x 267 mm) 

Belt table miter slot 

5/8 in. (16 mm) 

Disc sanding

 

 

Disc speed 

2100 RPM 

Abrasive disc size and grit 

10 in. (254 mm), 80 Grit 

Disc table 

Cast iron, 7-1/2 x 13 in. (191 x 330 mm) 

Disc table miter slot 

5/8 in. (16 mm) 

Disc table tilt 

45 deg. out 

Dust port, outside diameter 

2-1/2 in. (63.5 mm) 

Dimensions 

Overall dimensions, Sander and Stand (LxWxH) 

23 x 26 x 61 in. (584 x 660 x 1550 mm) 

Weights

 

Net weight (sander and stand) 

170 lbs. (77 kg) 

Shipping weight 

Sander only 

121 lbs. (55 kg) 

Stand only 

55 lbs. (25 kg) 

 

Table 1 

L = length, W = width, H = height 
RPM = revolutions per minute 
SFPM = surface feet per minute 
 

1

 Subject to local/national electrical codes.  

 

 

The specifications in this manual were current at time of publication, but because of our policy of continuous 
improvement, JET reserves the right to change specifications at any time and without prior notice, without incurring 
obligations.

 

 

 

 

 

Summary of Contents for J-4210




















Reviews: