Jet ETM-949 Operating Instructions Manual Download Page 21

Page: 21 / 52

ETM–949 | ETM–949EVS

10. Check for correct operation using the coarse feed

handle. If operating correctly, start the drive motor

and engage the power feed mechanism. Verify that

the power feed lever correctly engages and disengag-

es when driven by the drive motor.

10.6 TABLE LEAD SCREW BACKLASH

ADJUSTMENT

Refer to Figure 24.

The milling machine table is moved by a lead screw and
nut for each machine axis. For proper operation, there
must be clearance between the lead screw and the nut,
which results in backlash. A second lead screw nut is
provided to eliminate most of the backlash. The following
procedures provide instructions for obtaining acceptable
backlash.

Cross Feed Backlash Adjustment:

1. Use the cross feed crank to move the table to the

extreme rear of its travel.

2. Remove the pleated way cover.

3. Open the two chip guards enough to expose the

cross-feed adjustment nut (the nut that is toward the

rear of the nut bracket is not adjustable – only the front

nut is adjustable).

4. Loosen the two nut locking screws.

5. Turn the nut slightly to tighten it against the opposing
nut.

6. Tighten the two nut locking screws.

7. Using the cross-feed crank, move the table to the

middle position.

8. Set up a dial indicator to check cross-feed backlash.

Gently move the cross feed crank back and forth while

watching the dial indicator. Backlash should be be-

tween 0.003 inch and 0.005 inch.

9. If necessary, repeat the steps above to set backlash.

10. Install the pleated way cover.

Longitudinal Backlash Adjustment:

Refer to Figure 24.

1. Only one of the longitudinal lead screw nuts can be

adjusted. The other nut is fixed. The left hand nut is

typically adjustable. This can be determined by

looking at the nut from the underside of the table.

2. Loosen the two nut locking screws.

3. Turn the nut slightly to tighten it against the opposing
nut.

4. Tighten the two nut locking screws.

5. Using the longitudinal table crank, move the table to

the middle position.

6. Set up a dial indicator to check longitudinal backlash.

Gently move the crank back and forth while watching

the dial indicator. The backlash should be between

0.003 inch and 0.005 inch.

If necessary, repeat the steps above to set backlash.

Fig. 24

Table Lead Screw Components

Feed nut - end view

Cross-feed section view

Longitudinal feed section view

Slots allow adjustment
of thread tightness

Lock Screws

Threads in bore
accept lead screw

Leadscrew nut set

Knee
Casting

Graduated dial

Dial holder

Bearing retainer ring

Bearing
Bracket

Adjustable
nut

Rollpin

Sealed ball
bearings

Right bearing bracket

Bearing
retaining ring

Bearing bracket
cap screws

Longitudinal
lead screw nut set

Adjustable
nut

Left bearing bracket

Dial
lock
ring

Graduated
dial

Shim(s)

Dial holder

Nut bracket

(same part as cross-feed
section view)

Nut bracket

(same part as longitudinal
feed section view)

Summary of Contents for ETM-949





















































Search results

Summary of Contents for ETM-949

Reviews:

Related manuals for ETM-949

Brands by name

Popular brands

Jet ETM-949, Operating Instructions Manual

Search results

Summary of Contents for ETM-949

Reviews:

Related manuals for ETM-949

Brands by name

Popular brands