Jet-tech 737E Owner'S Manual Download Page 4

MANUFACTURERS LIMITED WARRANTY

 

 

MVP GROUP  CORPORATION  (Jet-Tech Systems)  hereby  warrants  all new  warewashers  bearing 

the name “JET-TECH” and installed within the continental United States of America or Canada to be 

free from defects in material and workmanship, under normal and regular usage and operation, for a 

period of one (1) year following the date of original installation (

unless  specified  otherwise

) but in 

no event can exceed eighteen (18) months from the date of shipment from the factory.

 

 

This warranty is valid 

ONLY 

for the original owner of the “Jet -Tech” unit and is not transferrable.

 

 

If a defect  in material(s)  or  workmanship  is detected  or found  to  exist  within  the above  stated 

period,  MVP  Group  Corp.  ,  at  its  sole  discretion,  shall  either  repair  or  replace  any  original 

equipment  manufacturers  part  which has  proven  to  fail  within  the  machine,  providing  that  the 

equipment has not been altered or tampered with in any manner, has been installed correctly as 

per the owner’s manual and maintained and operated in complete accordance with this manual.

 

 

The labor cost to repair or replace any part proven to be defective, as per above clause(s), shall be 

covered by MVP Group Corp. , within the continental United States of America or Canada provided 

that  prior  authorization  for  this  labor  was  approved  by  MVP Group  Corp.  ,  the  service  work  was 

performed  by an authorized  MVP Group Corp. , service  agency  and that  this  agency  installed  an 

original and genuine Jet-Tech  part in the machine. Any repair work performed by a non-authorized 

service  depot  remains  the  sole  responsibility  of  the  user and  MVP Group Corp. ,  will  not  be  held 

responsible.   

The  installation  of  any  generic  part  will  not  be  valid  and  therefore  voids  this 

warranty. 

All   authorized   labor   coverage   shall   be   limited   to   regular  hourly  rates   only.   Any 

supplemental hourly rates or charges, such as weekends, holidays  or emergency premiums remain 

the responsibility of the user.

 

 

MVP  Group  Corp.  ,  (Jet-Tech)  hereby  states  that  warranty  travel  time  shall  be  limited  to  and 

without exception, a round-trip total of two (2) hours OR mileage up to a maximum of one hundred 

(100)  miles  (160  KM)  roun   d-trip.  Any  charges  exceeding  those  stated  herein  must  have  prior 

authorization by the factory or will be at the customer’s expense.

 

 

Exceptions to above warranty are 

: (A) Damages resulting from shipping, handling or abuse. (B) 

Incorrect installation  and/or connections. (C) Adjustments or calibration of any parts. (D) Faults due 

to lack of regular maintenance or cleaning of any internal part(s). (E) Replacement of any wearable 

items  such  as  peristaltic  squeeze  tubing  or  gaskets.  (F)  Excessive  lime,  mineral,  alkali  or  hard 

water  conditions  (In  excess  of  6  grain)  and  (G)  Poor  results  due  to  use  of  an  incorrect  type  of 

detergent or rinse additive   (for no n-commercial  type  applications or products containing chlorine) 

and excessive or inadequate water temperature(s) or pressure conditions or incorrect use.

 

 

MVP  GROUP  CORPORATION 

STATES   THAT   THERE   ARE   NO   OTHER   WARRANTIES, 

EXPRESSED  OR   IMPLIED,    THAT   ARE   NOT    SET   FORTH   HEREIN,  MVP   GROUP 

CORPORATION  SHALL ASSUME NO OTHER RESPONSIBILIT Y, EITHER DIRECT OR NON  - 

DIRECT OR BE LIABLE  FOR ANY OTHER OR ADDITIONAL LOSS OR DAMAGE WHETHER 

BEING DIRECT OR CONSEQUENTIAL, AS A RESULT OF ITS EQUIPMENT.

 

 

 

 

 

Warranty

One year parts & labor (Continental USA and Canada).

 

 

 

 

The manufacturer reserves the rights to alter design and specifications  without notice.

 

 

 

 

 

4

 

Summary of Contents for 737E

















Reviews: