background image

16

GB

GB

GB

GB

GB

Declaration of conformity

This declaration is no assurance of characteristics in the sense of the product liability law. The safety notes
in the operation & maintenance instructions must be obeyed.

EC – Declaration of Conformity

We,

Lutz-Jesco GmbH

Am Bostelberge 19
D – 30900 Wedemark

hereby certify
that the product described in the following complies with the relevant fundamental
safety and sanitary requirements and the EC regulations mentioned below due to the
concept and design of the version sold by us.
If the product is modified without our consent, this declaration loses its validity.

Product description:

Perestaltic Pump

Model designation:

EASYDOS Peristaltic V

Relevant EC regulations:

EC Low-Voltage Directive (73/23/EEC)
EC Electromagnetic Compatibility Directive
(93/68/EEC)

Applied harmonized

EN 292-1 and EN 292-2,Safety of Machines

standards, especially:

EN 50081 Parts 1 and 2, EN 50082 Parts 1 and 2,
Electromagnetic Compatibility, Emission of Noise
and Noise Immunity

Applied national standards

VDE 0700, Teil 1

and technical specifications,
especially:

Date, Signature of Manufacturer: 2005/05/01 . . . . . . . . . . . . . . . . . . . . . . . . . .

Information on the signer:

Mr. Lucjan Gogolin, Head of Technical Office

This declaration is no assurance of characteristics in the sens of the product liability law.
The safety notes in the operating instructions must be observed.

Summary of Contents for EASYDOS Peristaltic V





















Reviews: