Jerr-Dan MPL Page 11 Operation Supplement Manual Download | Manualshive

Page: 11 / 16

background image

5-376-000106
REV. 0 - 09/07

23. Install safety chains and towing

lights.

CAUTION:

The Bottom Anchor Assembly (round tube) must never be higher
than the attachment point on the rear of the truck. The Stand Off
Bar Assembly acts as a pivot in the event of a sudden stop. This
will assure that the towed vehicle will not catapult forward onto the
deck of the MPL.

24. After the tow is complete, reverse

the procedure to unload the ve-
hicle.

25. Rotate the “CAM” handles on the

hold back bars 90° to the open
position and allow lower anchor
assembly to extend to the ground.

26. Open the underlift lockout valve,

then partially lower the boom and
underlift for easy access.

NOTE:

If the valve is not opened the
underlift tilt will not function.

Ea

st

ern

W

re

cke

r Sa

le

s

In

c

«
...
9
10
11
12
13
...
»

Summary of Contents for MPL

















Reviews:

No comments

Related manuals for MPL

Brand: Guldmann Pages: 16

Oxford In-situ Sling

Brand: Joerns Healthcare Pages: 4

Brand: BabyBjorn Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands