background image

 

 

 

 

 

 

 

 

2

 

MS30BT 

Safety Information 

 

To ensure full satisfaction with the product, please read the entire instruction manual. 

 

Keep instructions for future reference. 

 

Follow all operation guidelines and adhere to all safety warnings and cautions to ensure safe use. 

 

Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that 

produce heat. 

 

Only use attachments/accessories specified by the manufacturer. 

 

Never use harsh cleaning agents. Clean only with a dry cloth. 

When Driving 

Keep the volume level low enough to be aware of the road and traffic conditions. 

Protect from Water 

Do not submerge, as this can cause electrical shorts, fire or other damage. 

Protect from High Temperatures 

Exposure to direct sunlight for an extended period of time can produce very high temperatures inside your vehicle. Give the 

interior a chance to cool down before starting playback. Do not mount the radio within close proximity of the engine 

compartment.   

Use the Proper Power Supply 

This product is designed to operate with a 12 volt DC negative ground battery system. 

WARNING: 

 

DO NOT OPEN, DISASSEMBLE OR ALTER THE UNIT IN ANY WAY. Doing so may result in fire, electric shock or product 

damage. 

 

USE THE CORRECT AMPERE RATING WHEN REPLACING FUSE. Failure to do so may result in fire, electric shock or 

product damage. 

 

DO NOT INSTALL IN LOCATIONS THAT MIGHT HINDER VEHICLE OPERATION. Doing so may obstruct vision or 

hamper movement which can result in a serious accident. 

 

INSTALL THE WIRING SO THAT IT IS NOT CRIMPED OR PINCHED BY SCREWS OR SHARP METAL EDGES. Route 

the cables away from moving parts or sharp pointed edges. This will prevent crimping and damage to the wiring. If the 

wiring must pass through a metal hole, be sure to use a rubber grommet to prevent the wire's insulation from being cut by 

the metal edge of the hole. It is also recommended to apply sealing caulk to any opening that may potentially allow water 

to enter. 

 

Be sure to choose a location that is flat and has clearance above the unit to prevent any damage, as well as allow for 

ventilation. 

 

Before drilling any holes, carefully inspect the area underneath and behind the mounting surface where the device will be 

mounted to make sure it will not interfere with existing wires, fuel lines, the fuel tank or any other objects that could be 

damaged. 

 

Always disconnect the vehicle negative battery terminal during installation to prevent accidental shorting. 

 

 

Summary of Contents for MS3ARTL
















Reviews: