Power Supply:
AC 120V ~ 60Hz
Radio Frequency Coverage:
AM: 535 - 1705 KHz
FM: 88 - 108 MHz
Specifications subject to change without notice.
TROUBLE SHOOTING
1) Turn on the unit by
pressing
the POWER
BUTTON
(3),
the
Power Indicator lights.
2) Select the desired band
(AM/FM/FM St.) with the
FUNCTION
Control
(5).
3) Tune in
your
desired station using the TUNING Knob (7). If the FM ST. band was chosen, the FM STEREO
indicator (6) will light up whenever a stereo broadcast is received. To receive a weak (noisy) FM station,select FM
band by setting the FUNCTION knob(5) to
the
FM position .The FM STEREO indicator (6) will go off and the
reception may be improved, but the sound is
now
monaural (MONO).
4) Adjust the VOLUME
Control
(1) to the desired sound level.
5) To turn the unit off, press the POWER Knob (3) again, The Power Indicator (4) goes off.
Power
button
on
(pushed in)
, but no power
* Check power to wall plug.
* Check AC cord connection to wall plug.
Power Indicator is on, but no sound from speaker
* Check FUNCTION selector.
* Check VOLUME setting
* Make sure headphones are not plugged in.
Poor FM reception
*
Untie
and fully extend
the
FM wire antenna for best reception.
-
Do not
plug in
the power cord until all other connections have been made.
-
Do not expose this
product
to liquid.
Power
Button
After using the unit, switch off the power by releasing the POWER
Button.
Cleaning the Unit
To
clean
, simply wipe with soft clean
damp (never wet)
cloth.
Never use solvents or abrasive cleaners.
Stylus (needle) Replacement
Replace a worn stylus
by following the directions below
1) Raise the “Tone Arm”.
2) To remove the old stylus
needle
, pull out the stylus assembly in the direction
shown, holding the head shell with your other hand.
3) Then install the new stylus
needle
by pushing it gently into the cartridge
(hold by the edge to prevent damage to the stylus) until it clicks into place.
CARE & MAINTENANCE
TUNER OPERATION
PHONO OPERATION
SPECIFICATIONS
HINTS FOR BEST RECEPTION
FM: The receiver has a built-in FM antenna (8) hanging from the rear cabinet. This wire should be completely
unraveled and extended for best reception.
AM : This unit is equipped with a built-in directional ferrite antenna. Rotate the unit to obtain the best reception.
Note:
Flip-up the clear
stylus protector
to expose the needle
. Be sure that the tone arm
is detached from
the
tone arm r
est
(13)
before operat
ing
.
1) Turn on the unit with the POWER
Button
(3). The POWER Indicator (4) will
light up.
2) Set the FUNCTION
Selector
(5) to the PHONO position.
3) Set the SPEED SELECTOR (14) to the proper position depending on
the record to be played. Three speeds (33 rpm, 45 rpm,
78 rpm)
can be selected. When 45 rpm is selected, use the 45 rpm
ADAPTOR (15).
4) Place the record on the platter (if required, use the 45 rpm adaptor)
5) Lift the tone arm (12) from the rest
(13)
and
t
he platter will begin to rotate
as you move it towards the record
.
6) Place the
needle of the
tone arm (12)
on the record at the
desired position.
7) Adjust
the
VOLUME
control
(1) to the desired sound level.
8) At the end of the record, the platter will continue to rotate
until the tone arm (12) is returned to the rest (13)
.
Note:
The turntable platter will not automatically stop when the record finishes playing. This is to allow extended play
records to play all the way through without prematurely stopping before the tone arm reachs the end of the record
(center area). Don't allow the record to continue turning for extended periods of time once the tone arm (12)
reaches the center of the record. This could prematurly wear out the stylus needle.
9
)
Stop the Turntable by pressing the POWER Button (3).
Lift the
tone arm
(12) and return it to the
rest
(13).
IMPORTANT:
Do not turn or stop the Turntable
platter
manually. Moving or jarring the Turntable
platter
without securing
the Tone Arm Clamp could result in damage to the T
one Arm or Stylus
.
SERVICE
4
5
HXT-1058 IB JENS 001 REV0.P65
5/9/2006, 4:03 PM
3
