Jensen DC 9520 A Installation Manual Download Page 7

Page: 7 / 12

KDC 9520

Wiring Diagram–Advanced Installation

If you are installing new speakers or amplifiers or replacing an aftermarket installation, use this diagram.

Fuses

When replacing a fuse, make sure new
fuse is correct type and amperage.
Using an incorrect fuse could damage
radio. The KDC 9520 uses a 10 amp
fast blow AGC fuse as part of rear wiring
harness.

Memory
Connect to battery or 12 volt
power source that is always live.

The radio will not work if this
wire is not connected.

Accessory
Connect to existing radio wire or
radio fuse.

Ground
Connect to ground terminal or
clean, unpainted metal part of
chassis.

Power Antenna
Connect to power antenna or
amplifier. If not used, tape bare
end of wire.

Go to “Testing” on page 8.

LF–

white/black

white

LF+

RF–

gray/black

gray
RF+

LR–

green/black

green

LR+

RR–

violet/black

violet

RR+

AMP

Amplifier wiring

(See amplifier instructions)

RCA-to-RCA cables

(not supplied)

–

Black

Yellow

Red

AMP

Filter

Box

Antenna

extender

cable (not

supplied)

CD Changer

Antenna

Jack

Back of Receiver

Dark Blue

KDC9520 _EIN.p65

3/14/00, 1:28 PM

Summary of Contents for DC 9520 A













Search results

Summary of Contents for DC 9520 A

Reviews:

Brands by name

Popular brands

Jensen DC 9520 A, Installation Manual

Search results

Summary of Contents for DC 9520 A

Reviews:

Brands by name

Popular brands