Jenn-Air JUIFN15HX00 Installation Manual Download | Manualshive

Page: 13 / 42

background image

DOOR REVERS

AL

DOOR REVERSAL

DOOR REVERSAL | 13

2

Remove the screws attaching top and
bottom hinge covers using an 3/16" hex
driver.

Crush Hazard

Articulated hinges are self closing and many
pinch points exist prior to cabinet
installation.

Do not remove hinge covers until product is
ready to be installed.

Failure to follow these instructions can result
in crush, cut, or pinch injuries.

WARNIN

G

Hinge cover

3

Using pliers, remove the hinge covers
from the top and bottom hinges.

NOTE:

Save the hinge covers for

future use. Reinstall the hinge covers
if product is removed from cabinet
installation.

«
...
11
12
13
14
15
...
»

Summary of Contents for JUIFN15HX00











































Reviews:

No comments

Related manuals for JUIFN15HX00

Brand: GE Pages: 12

Brand: Caffitaly System Pages: 80

Brand: Caffitaly System Pages: 16

Brand: Caffitaly System Pages: 60

Brand: Gaggia Pages: 152

Brand: Fagor Pages: 21

Brand: Fagor Pages: 29

Brand: Fagor Pages: 17

Brand: Fagor Pages: 122

M39 Dosatron TE

Brand: La Cimbali Pages: 50

Brand: La Cimbali Pages: 15

Brand: La Spaziale Pages: 11

Brand: La Spaziale Pages: 16

Brand: BALAY Pages: 2

Brand: Hoshizaki Pages: 33

nina plus SIN026X

Brand: Saeco Pages: 24

Brand: Qilive Pages: 96

AROMATICA U27.51

Brand: Rotel Pages: 73

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands