background image

6

Locate Wall Stud(s)

NOTE:

 If no wall studs exist within the cabinet opening, do not 

install the microwave oven.
See illustrations in “Possible Wall Stud Configurations.”

1.

Using a stud finder, locate the edges of the wall stud(s) within 
the opening.

2.

Mark the center of each stud, and draw a plumb line down 
each stud center. See illustrations in “Possible Wall Stud 
Configurations.”

Possible Wall Stud Configurations

These depictions show examples of preferred installation 
configurations with the mounting plate.

NOTE:

 If wall stud is within 6" (15.2 cm) of the vertical centerline 

(see “Mark Rear Wall” section), only recirculation or roof venting 
installation can be done.

Figure 1 - One Wall Stud

NOTE:

 Holes are for installation with 1 lag screw into the wall stud 

and 2 toggle bolts through the drywall.

Figure 2 - Two Wall Studs

NOTE:

 Holes are for installation with 2 lag screws into the wall 

studs.

Mark Rear Wall

The microwave oven must be installed on a minimum of 1 wall 
stud, preferably 2, using a minimum of 1 lag screw, preferably 2.

1.

Using measuring tape, find and clearly mark the vertical 
centerline of the opening.

A. Centerline

2.

Mark the centerline 14

¹⁄₂

" (36.8 cm) down from bottom edge of 

the upper cabinet (or flush line, if upper cabinet has a hanging 
front edge – see illustration).

3.

Using a straightedge, draw a level, horizontal line through the 
mark made in Step 2. This represents the top edge of the 
mounting plate.

4.

Remove the mounting plate and check the markings:

The top edge line must be 14

¹⁄₂

" (36.8 cm) from the bottom of 

the upper cabinet, and must be level.

A. Cabinet opening vertical centerline
B. Holes for toggle bolts 

C. Wall stud centerlines
D. Holes for lag screws

E. Support tabs

F. Mounting plate center marker

A

B

B

C

D

E

E

F

D

A

C

C

F

E

E

D

A. Rear wall
B. Hanging front edge of upper cabinet

C. Flush line
D. Mark for top edge of mounting plate

E. Bottom of smooth bottom upper cabinet

A

A

A

C

D

D

E

B

14

¹⁄₂

"

(36.8 cm)

Upper cabinet bottom

Top edge of mounting plate

14

¹⁄₂

"

(36.8 cm)

Centerline

Summary of Contents for JMV8208DB













Reviews: