Jehnert 45180 Installation Instructions Manual Download | Manualshive

Page: 5 / 10

background image

08.10.09 10:23

Seite 5 von 8

Example

Installation Instructions Product-Ident: 45180

7 Fastening doorboard

7.1

Screw in the screws supplied with. Affix the doorboard to the door card.

Screw all screws only hand-tight . Secure all M4-screws with washers and nuts.

TIP:

Treat the screw thread with a liquid for screw-in type fuse. (Speaker vibrations may loosen the screws after

some time).

7.2

Check again for precise fit and tighten the screws.

All cutting edges of the doorboard must fit to the door card snugly all around without gap!

«
...
3
4
5
6
7
...
»

Summary of Contents for 45180











Reviews:

No comments

Related manuals for 45180

Brand: Targa Pages: 113

Brand: Yamaha Pages: 24

Brand: EAW Pages: 2

Brand: EAW Pages: 2

Brand: EAW Pages: 2

Brand: Fbt Pages: 16

Brand: Fbt Pages: 36

Brand: Battery Watering Technologies Pages: 2

Brand: EAW Pages: 4

Brand: Cambridge SoundWorks Pages: 11

Brand: J&M Pages: 8

Brand: Aiwa Pages: 12

Porsche Design P9611

Brand: Navigon Pages: 25

Brand: Yealink Pages: 52

Brand: Cadillac Pages: 114

Brand: Bauhn Pages: 28

Price Center 451

Brand: Polycom Pages: 4

Brand: REV Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands