background image

25

11.2. Welding torch

Part

Check

Remarks

Nozzle

1. Check if the nozzle is fixed firmly

and distortion of the tip exists.

Possible gas leakage occurs due to the unfixed nozzle.

2. Check if there is spatter sticking on

the nozzle.

Spatter possibly leads to the damage of torch. Use
anti

spatter to eliminate the spatter.

Contact tip

1.

Check if the contact tip is fixed
firmly.

Unfixed contract tip possibly leads to unstable arc.

2.

Check if the contact tip is physically
complete.

The physically incomplete contact tip possibly leads to
unstable arc and arc automatically terminating.

Wire feeding

hose

1. Make sure that there is the

agreement of wire and wire feed
tube.

Disagreement of the diameters of wire and wire feed tube
possibly leads to the unstable arc. Replace it/them if
necessary.

2. Make sure that there is no bending

or elongation of wire feed tube.

Bending and elongation of wire feed tube possibly leads to
the unstable wire feed and arc. Replace it if necessary.

3. Make sure that there is no dust or

spatter accumulated inside the
wire feed tube, which makes the
wire feed tub blocked.

If there is dust or spatter, remove it.

4. Check if the wire feed tube and

O

shaped

seal

ring

are

physically complete.

The Physically incomplete wire feed tube or O

shaped seal

ring possibly leads to the excessive spatter. Replace the wire
feed tube or O

shaped seal ring if necessary.

Part

Check

Remarks

Diffuser

1. Make sure that the diffuser of

required specification is installed
and is unblocked.

Defection weld or even the damage of torch occurs due to
the non

installation of diffuser or the unqualified diffuser.

Summary of Contents for BLUEARC-200MSTI































Reviews: