background image

 

 

Installation Instructions for 79009 
Bottle Jack 

20 Ton 
 

Save the receipt, warranty and these instructions. It is important that you read the entire manual to become familiar with 
this product before you begin using it. 
This machine is designed for certain applications only. The distributor cannot be responsible for issues arising from 
modification. We strongly recommend this machine not be modified and/or used for any application other than that for 
which it was designed. If you have any questions relative to a particular application, DO NOT use the machine until you 
have first contacted the distributor to determine if it can or should be performed on the product. For technical questions 
please call 1-800-345-4545.  
 

INTENDED USE 

This Air/Hydraulic Bottle Jack is designed for lifting. The jack can be used vertically or angled to 3 degrees form vertical 
position. After lifting, loads must be immediately supported by appropriate means. Each model is suitable for use in 
lifting or positioning vehicles, machinery, houses and/or other building structures. These jacks comply with ASME PALD 
Standards. For air actuated use, ensure that your air source has a working range of 100-120 PSI. 
 

TECHNICAL SPECIFICATIONS 

 

Description 

Item 

79009 

Maximum Capacity 

40,000 lbs. 

Minimum Lift Height 

10-7/16 in. 

Maximum Lift Height 

20-1/16 in. 

Screw To Adjustment 

3-1/8 in. 

Rated Air Pressure PSI 

Min. 100 - Max. 120 PSI 

Product Size 

6-3/8 in. x 9-7/16 in. x 20-1/8 in. 

Weight 

39 lbs. 

Safe Operating Temperature is between 40°F - 105°F (4°C - 41°C) 
 

GENERAL SAFETY RULES 
WARNING:

 

Read and understand all instructions.

 Failure to follow all instructions listed below may result in serious 

injury. 

 

CAUTION:

 

Do not allow persons to operate or assemble this Jack until they have read this manual and have 

developed a thorough understanding of how the Jack works. 

 

WARNING:

 

The warnings, cautions, and instructions discussed in this instruction manual cannot cover all 

possible conditions or situations that could occur.

 It must be understood by the operator that common sense and 

caution are factors that cannot be built into this product, but must be supplied by the operator. 
 

SAVE THESE INSTRUCTIONS

 

 

 

 

                                         1-800-345-4545   jegs.com

 

Summary of Contents for 79009

















Reviews: