Jeep Liberty Owner'S Manual Download Page 28 | Manualshive

Page: 28 / 542

Jeep Liberty Owner'S Manual Download Page 28

2. With the RKE transmitter buttons facing down, use a
flat blade tool to pry the two halves of the RKE transmit-
ter case apart. Make sure not to damage the seal during
removal.

3. Remove and replace the battery. Avoid touching the
new battery with your fingers. Skin oils may cause
battery deterioration. If you touch a battery, clean it with
rubbing alcohol.

4. To reassemble the RKE transmitter case, snap the two
halves together.

5. Reinstall and tighten the screw until snug (if
equipped).

General Information

This device complies with Part 15 of FCC rules and with
RS-210 of Industry Canada. Operation is subject to the
following conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference that may be
received including interference that may cause undesired
operation.

Separating Case Halves

26

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

«
...
26
27
28
29
30
...
»

Summary of Contents for Liberty































































































































































































































































































































































































































































































































































Reviews:

No comments