manualshive.com logo in svg

Jeep Grand Cherokee SRT8 2012, Owner'S Manual

Share
Download
Jeep Grand Cherokee SRT8 2012 Owner'S Manual Download Page 193

NOTE:

If the vehicle is moving less than 10 mph

(16 km/h), delay times will be doubled.

Windshield Washer Operation

To use the washer, push on the end of the lever (toward
the steering wheel) and hold while spray is desired. If the
lever is pushed while in the intermittent setting, the

wipers will turn on and operate for several wipe cycles
after the end of the lever is released, and then resume the
intermittent interval previously selected.

If the end of the lever is pushed while the wipers are in
the off position, the wipers will operate for several wipe
cycles, then turn off.

Intermittent Wiper Operation

Windshield Washer Operation

3

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

191

Summary of Contents for Grand Cherokee SRT8 2012





























































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands