background image

METRIC SYSTEM

DESCRIPTION

The metric system is based on quantities of one,

ten, one hundred, one thousand and one million.

The following chart will assist in converting metric

units to equivalent English and SAE units, or vise
versa.

CONVERSION FORMULAS AND EQUIVALENT VALUES

MULTIPLY

BY

TO GET

MULTIPLY

BY

TO GET

in-lbs

x 0.11298

= Newton Meters
(N·m)

N·m

x 8.851

= in-lbs

ft-lbs

x 1.3558

= Newton Meters
(N·m)

N·m

x 0.7376

= ft-lbs

Inches Hg (60° F)

x 3.377

= Kilopascals (kPa)

kPa

x 0.2961

= Inches Hg

psi

x 6.895

= Kilopascals (kPa)

kPa

x 0.145

= psi

Inches

x 25.4

= Millimeters (mm)

mm

x 0.03937

= Inches

Feet

x 0.3048

= Meters (M)

M

x 3.281

= Feet

Yards

x 0.9144

= Meters

M

x 1.0936

= Yards

mph

x 1.6093

= Kilometers/Hr.
(Km/h)

Km/h

x 0.6214

= mph

Feet/Sec

x 0.3048

= Meters/Sec (M/S)

M/S

x 3.281

= Feet/Sec

mph

x 0.4470

= Meters/Sec (M/S)

M/S

x 2.237

= mph

Kilometers/Hr. (Km/h)

x 0.27778

= Meters/Sec (M/S)

M/S

x 3.600

Kilometers/Hr. (Km/h)

COMMON METRIC EQUIVALENTS

1 inch = 25 Millimeters

1 Cubic Inch = 16 Cubic Centimeters

1 Foot = 0.3 Meter

1 Cubic Foot = 0.03 Cubic Meter

1 Yard = 0.9 Meter

1 Cubic Yard = 0.8 Cubic Meter

1 Mile = 1.6 Kilometers

Refer to the Metric Conversion Chart to convert

torque values listed in metric Newton- meters (N·m).
Also, use the chart to convert between millimeters
(mm) and inches (in.) (Fig. 4).

WJ

INTRODUCTION

5

Summary of Contents for 2002 WG Grand Cherokee











Reviews: