Jeds Peds More! More! Moore! FV1 Manual Download | Manualshive

Page: 19 / 25

background image

© Jeds Peds

[email protected]

More! More! Moore!

Pag

e

19

The next step involves undoing the tip wires from the PCB as they will now move to the 3PDT. It is a
couple of steps backwards I am afraid, but nothing to arduous.

Once you have de-soldered the three wires, clean the joints up and re solder fresh wires to them.
About 2 inches long will be perfect, a little longer if you wish. They will be cut to length later.

Cut the ground joint and strip the ends of all wires again so they are fresh.

The PCB should have 4 wires coming from it all about 5/6 inches long.

«
...
17
18
19
20
21
...
»

Summary of Contents for More! More! Moore! FV1


























Reviews:

No comments

Related manuals for More! More! Moore! FV1

Brand: C-Dax Pages: 39

Brand: G-Lab Pages: 24

Brand: Mr. Black Pages: 2

Brand: Fulltone Musical Products Pages: 2

Brand: M-Audio Pages: 12

Brand: M-Audio Pages: 45

Brand: Whirlwind Pages: 2

U.S Audio MPM-1

Brand: Whirlwind Pages: 6

Brand: Whirlwind Pages: 6

JERRY CANTRELL CRY BABY

Brand: Dunlop Pages: 4

Brand: Gemini Pages: 20

Brand: Ritual Electronics Pages: 14

Brand: RFX Pages: 2

Brand: T-Rex Pages: 8

Brand: Galaxy Industries Pages: 2

Brand: Peavey Pages: 16

Brand: Peavey Pages: 18

Brand: Ibiza Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands