background image

 

© Jeds Peds 

[email protected] 

EOTS 

Pag

e

20

 

The Footswitch. 
 

Have a look at the footswitch. It has 9 pins. The orientation of the switch is crucial. If you do it wrong 
your switch will not work, you might ruin it and you will certainly have to un do it. 
 

 

 
 

There are various ways to connect a switch to a circuit. Most people think  you get a ‘true bypass’ 
switch. It’s just a method of wiring. A switch is merely a switch.

 

 
There are two ways you can connect the switch. One uses a PCB and one involves manual wiring.  
 
I have designed a PCB specifically for the footswitch and whilst over time the layout of the  switch 
may change slightly, the mechanics of it do not. In its simplest form, it solders to the switch and the 
wires solder to its pads. 
 

 
The  two  fit  together  like  this.  Take  some  time  to 
study the footswitch and PCB. 
 

NOTE:

 the lugs run from left to right as I said above. 

 
The  PCB  has  two  sides,  it  must  go  on  like  this.  The 

other side looks quite different and does not say ‘jeds 
peds’ 

on it. 

 
 
 
 

Once you are satisfied it is on the right way then it must be soldered into place, 

but

 

don’t do it yet as 

I want to explain a second method of switch wiring that you may decide suits you better.  
 
 

 

The  pins  on  the  switch  must  run  left  to 
right like this, so the top row of pins would 
be 1, 4, and 7. 
 
If  you  put  it  in  with  1,  2, and  3  across  the 
top row you are wrong.  
 

In  reality  there  is  no  ‘pin  1’,  it’s  just  used 

here  as  a  reference.  So,  if  you  turn  it  180 
degrees,  pin  9  could  also  be  pin  1.  The 
switch will still work providing the lugs are 
horizontal. 

 

Summary of Contents for E.O.T.S


























Reviews: