Jedia JSC-132AU Operating Instructions Manual Download Page 10

8

O

PERATING METHOD 

(동작 방법)

1) 기기의 조정

AC 및 DC 전원을 모두 차단합니다.
전원을 인가합니다.
TP3 혹은 TP4가 AC 1.767Vrms가 되도록 VR3을 조정합니다.
TP7이 AC 3.536Vrms가 되도록 VR1를 조정합니다.
J9의 SHORT RING을 제거합니다.
TP8이 DC 0Vrms가 되도록 VR2를 조정합니다.
J9의 SHORT RING을 원위치에 연결합니다.
J15의 "CAL" 혹은 "REM" 위치에 SHORT RING을 연결하면 다음
과 같이 표시됩니다.

1) Calibration

Power AC/DC off.

5. INITIALIZATION

5. 기기의 초기화

주의 : 부적절한 초기화 실행시 기기의 성능에 오차를 발생시킬
수 있습니다.
초기화 실행시에는 AC 조정을 위하여는 오디오 아날라이저와
오실로스코프를 사용하고, DC조정을 위하여는 디지털 메타를
사용합니다.

WARNING:

 

It may occar difference in case of inproper initialization. So you 

are strongly not recommand to initialize unit except necessity.

Use audio analyzer and oscilloscope for AC adjustment.

Power on.

Adjust VR3 of TP4 or TP7 to be AC 1.767Vrms.

Adjust VR3 of TP7 to be AC 3.536Vrms. 

Remove short ring of J9.

Adjust VR2 of TP8 to be DC 0Vrms

Connect short ring of J9.

When connecting short ring to "REM" or "CAL" of J15, it

displays as below.

2) 메모리 소거

2) Memory Clear

Power AC/DC off.

Connect short ring to  "MCLR" or "CLR" of J15.

Power AC/DC "on" then, it displays as follows.

When clear memory successfully, it displays as follow.

It displays as follows when removing short ring on the "CLR",

"MCLR" of J15.

If calibration is finished successfully.

It displays as below.

Remove short ring on the "J15" or "REM" after checking

repeat of 1-8, "1-9" processing.

(SW = Switch)

(Int.=interval), (H=Hour, M=minute)

C a l i b r a t i o n !

1 0 2 2

C a l i b r a t i o

d !

n

n

e

R e m o v e

' C A L '

S W !

C a l i b r a t i o

d !

n

n

e

R e m o v e

' C A L '

S W !

C a l i b r a t i o

d !

n

n

e

R e m o v e

' C A L '

S W !

I n t .

0 0 H 0 3 M

T i m e S t o r e !

I n t .

0 0 H 0 3 M

T i m e S t o r e !

I n t .

W o r k i n g O k !

T i m e S t o r e !









기기의 조정이 완료되면 다음과 같이 표시됩니다.


AC 및 DC 전원을 모두 차단합니다.
J15의 "MCLR" 혹은 "CLR" 위치에 SHORT RING을 연결합니다.
전원을 인가하면 다음과 같이 표시됩니다.

메모리가 모두 소거되면 다음과 같이 표시되어 점멸합니다.

J15의 "MCLR" 혹은 "CLR" 위치의 SHORT RING을 제거하면
다음 순서로 표시됩니다.

(이후는 동작 방법에 준하여 수행됩니다.)







1-8과 1-9의 표시가 반복되는 것을 확인 후 J15의 "CAL" 혹은
"REM" 위치의 SHORT RING을 제거합니다

Summary of Contents for JSC-132AU













Reviews: