JCM GLOBAL UBA Pro Series Operation And Maintenance Manual Download Page 71

Page: 71 / 132

UBA™ Pro Series

Universal Banknote Acceptor

S e c t i o n 6

P/N 960-000211R_Rev. A

6 - 1

This section provides Calibration and Performance

Testing instructions for the UBA™ Pro Series Uni-

versal Banknote Acceptor (UBA Pro). This section

contains the following information:

•

Tool Requirements

•

Installation Procedures

•

JCM Tool Suite Standard Edition Mode

Performance Test Using a PC

•

Performance Test without a PC

Tool Requirements

Figure 6-1 illustrates and identifies the tools and

equipment interconnects necessary to download

and install the Unit.

Installation Procedures

Perform the following steps to install the “

JCM Tool

Suite Standard Edition

” Application Software and

USB Drivers. (Refer to Figure 6-1 for the neces-

sary Tool and Harness Connections .)

Part 1 - JCM Tool Suite Installation

1. Copy the “

JCMToolSuiteStandardEdition.zip

”

Application Software and extract on to the Desk-

top.

2. Double-click on “

Setup.exe

”(Figure 6-2

3. The “

JCM Tool Suite Standard Edition - Install

Shield Wizard

” Screen shown in Figure 6-3 will

appear.

4. Click the “

Next>

”

Button (Figure 6-3

6 CALIBRATION AND TESTING

Figure 6-1

Tool and Harness Connections

Figure 6-1

Tool and Harness Connections

a) UBA Pro Unit
b) Power Supply
c) PC (OS: Windows

7/8/10)

(USB Driver Installed)

d) USB Cable



) USB Type-A (PC Side)



) USB Type-C (UBA Pro Side)

e) Application Software*



(JCM Tool Suite Standard Edition)

f) Reference Paper (KS-101)

*. Containing USB Downloader, Sensor Calibration,

Performance Test programs and Utility Function.

NOTE: Do Not put too much

pressure on the USB Cable

to avoid the risk of damage

to the UBA Pro’s PCB.

NOTE: Uninstall the current version of the

JCM Tool Suite application software

installed on your PC before updating to a

newer version.

Figure 6-2

JCM Tool Suite Installation 1

Figure 6-2

JCM Tool Suite Installation 1

Figure 6-3

JCM Tool Suite Installation 2

Figure 6-3

JCM Tool Suite Installation 2

Summary of Contents for UBA Pro Series





































































































































Search results

Summary of Contents for UBA Pro Series

Reviews:

Related manuals for UBA Pro Series

Brands by name

Popular brands

JCM GLOBAL UBA Pro Series, Operation And Maintenance Manual

Search results

Summary of Contents for UBA Pro Series

Reviews:

Related manuals for UBA Pro Series

Brands by name

Popular brands