background image

P/N 960-000213R_Rev.A 

© 2020, JAPAN CASH MACHINE CO., LTD. 

2 - 1 1

Installation

UBA Pro RT/RQ™ Series Banknote Recycler 

Section 2

Preventive Maintenance

Refilling Banknotes

Banknotes can be refilled into the Recycler by 

using the UBA Pro Unit.

To refill Banknotes into the Recycler, perform the 

following procedure:

1.  Insert Banknotes note-by-note in a single fashion 

into the Insertion Slot or Bezel (Figure 2-11).

Collecting Banknotes

To collect Banknotes from the Recycler, perform 

one (1) of the following two (2) procedures.

Collecting Banknotes into the Cash Box by 

the Collect Button

1.  Press the Collect Button on the RT/RQ Unit (Fig-

ure 2-12 

a

).

2.  Remove the Cash Box (Figure 2-13 

a

).

3.  Use the appropriate User-supplied Key(s) to 

unlock the Cash Box (Figure 2-13 

b

).

4.  Open the Cash Box Door and remove the col-

lected Banknotes (Figure 2-13 

c

).

Collecting Banknotes into the Cash Box by 

Command

1.  Send a Command to the RT/RQ Unit from the 

Host Machine in order to collect Banknotes.

2.  Remove the Cash Box (Figure 2-13 

a

).

3.  Use the appropriate User-supplied Key(s) to 

unlock the Cash Box (Figure 2-13 

b

).

4.  Open the Cash Box Door and remove the col-

lected Banknotes (Figure 2-13 

c

).

Dispense Settings

Dispensing Banknotes from each Drum of the 

Recycler to the Insertion Slot or the Bezel is possi-

ble. Banknote denomination dispensing is prede-

termined by settings made for each Drum.

To change the dispensable Banknote denomination 

values, replace the Recycler with another Unit con-

taining the different denomination settings.

Clearing a Banknote Jam

Find where a Banknote Jam occurred

Check each LED to determine where and/or in 

which Unit a Banknote is jammed (Refer to “LED 

Flashing Patterns” on page 2-5).

NOTE: Do Not manually refill the 

Banknotes directly into the Recyclers.

Figure 2-11 

Refilling Banknotes 

Figure 2-11 

Refilling Banknotes

NOTE: Enable the Collect Button function 

by sending a Command from the Host 

Machine (disabled by default). 

NOTE: The Banknotes in each Drum 

will be transported note-by-note into 

the Cash Box.

Figure 2-12 

Collecting Banknotes 1 

Figure 2-12 

Collecting Banknotes 1

a

Figure 2-13 

Collecting Banknotes 2 

Figure 2-13 

Collecting Banknotes 2

a

b

c

NOTE: The Banknotes in each Drum 

will be transported note-by-note into 

the Cash Box.

NOTE: Before setting the Recycler’s 

denomination values, check the Banknote 

sizes against the Recycler’s size limitation 

settings (Refer to “Technical Specifications” 

on page 1-7). This operation should be 

performed once appropriate Operator 

training has been completed.

NOTE: Do Not re-insert a removed 

Banknote caused by Banknote Jam or 

error.

Summary of Contents for UBA Pro RT Series





































































































































































































Reviews: