JCM GLOBAL UBA Pro RT Series, Operation And Maintenance Manual

Page: 116 / 196

P/N 960-000213R_Rev.A © 2020, JAPAN CASH MACHINE CO., LTD.
6 - 2 4
Section 6 UBA Pro RT/RQ™ Series Banknote Recycler Calibration and Testing
Recycler Solenoid Test (RT Transport)
To run the Recycler Solenoid on the RT Transport
side, proceed as follows:
1. Remove electrical power.
2. Set the DIP Switches of the UBA Pro Unit as
below (Figure 6-119).
3. Set the DIP Switches of the RT/RQ Unit as below
(Figure 6-120).
4. Apply electrical power.
5. Confirm that the Status LED/Collect Button is lit
at Green Color and then turns off.
6. To start the Test, set the UBA Pro DIP Switch #8
to
OFF
(Figure 6-122).
7. The Solenoid will start operating when it func-
tions properly.
8. Set the UBA Pro DIP Switch #8 to
ON
to end the
test.
Drum 1 Motor Test (RT Transport)
To run the Recycler Solenoid on the RT Transport
side, proceed as follows:
1. Remove electrical power.
2. Set the DIP Switches of the UBA Pro Unit as
below (Figure 6-123).
3. Set the DIP Switches of the RT/RQ Unit as below
(Figure 6-124).
4. Apply electrical power.
5. Confirm that the Status LED/Collect Button is lit
at Green Color and then turns off.
6. To start the Test, set the UBA Pro DIP Switch #8
to
OFF
(Figure 6-126).
7. The Drum 1 of the Recycler will start winding
the Tape until it reaches to “End” and then to
“Full” position back and forward repeatedly.
8. Set the UBA Pro DIP Switch #8 to
ON
to end the
test.
Figure 6-119 Recycle
Figure 6-119 Recycle Solenoid Test
(RT Transport) 1
DIP Switches #1, #2, #6, #8 ON
ON
1 2 3 4 5 6 7 8
Figure 6-120 Recycle
Figure 6-120 Recycle Solenoid Test
(RT Transport) 2
DIP Switch #5 ON
ON
1 2 3 4 5 6 7 8
NOTE: Wait for the Status LED to turn off
in order to run the test properly.
Figure 6-121 Recycle Sole-
Figure 6-121 Recycle Solenoid Test
(RT Transport) 3
Green ON
OFF
Figure 6-122 Recycle
Figure 6-122 Recycle Solenoid
Test (RT Transport) 4
DIP Switch #8 OFF
ON
1 2 3 4 5 6 7 8
NOTE: Confirm the functionality aurally by
the sound that the Solenoid is making
while in the operation.
Figure 6-123 Drum 1
Figure 6-123 Drum 1 Motor Test (RT Transport) 1
DIP Switches #1, #2, #6, #8 ON
ON
1 2 3 4 5 6 7 8
Figure 6-124 Drum 1
Figure 6-124 Drum 1 Motor Test (RT Transport) 2
DIP Switch #6 ON
ON
1 2 3 4 5 6 7 8
NOTE: Wait for the Status LED to turn off
in order to run the test properly.
Figure 6-125 Drum 1 Motor
Figure 6-125 Drum 1 Motor Test (RT Transport) 3
Green ON OFF
Figure 6-126 Drum 1
Figure 6-126 Drum 1 Motor Test (RT Transport) 4
DIP Switch #8 OFF
ON
1 2 3 4 5 6 7 8