background image

SO53 3LE

Customer Helpline 

0845 600 5526

GENERAL POwER tOOL sAfEty wARNINGs

 

wARNING! Read all safety 
warnings and all instructions.

 

Failure to follow the warnings and 
instructions may result in electric 
shock, fire and/or serious injury.

save all warnings and instructions 
for future reference.

The term "power tool" in the 
warnings refers to your electric 
(corded) power tool or battery-
operated (cordless) power tool.

1. work area safety

a)  Keep work area clean and well 
lit. 

Cluttered or dark areas invite 

accidents.

b)  Do not operate power tools in 
explosive atmospheres, such as in 
the presence of flammable liquids, 
gases or dust. 

Power tools create 

sparks which may ignite the dust 
or fumes.

c)  Keep children and bystanders 
away while operating a power tool. 

Distractions can cause you to 
lose control.

2. Electrical safety

a)  Power tool plugs must match 
the outlet. Never modify the plug 
in any way. Do not use any adapter 
plugs with grounded power tools. 

Unmodified plugs and matching 
outlets will reduce risk of electric 
shock.

b)  Avoid body contact with 
grounded surfaces, such as pipes, 
radiators, ranges and refrigerators. 

There is an increased risk of 
electric shock if your body is 
grounded.

c)  Do not expose power tools 
to rain or wet conditions. 

Water 

entering a power tool will increase 
the risk of electric shock.

d)  Do not abuse the cord. Never 
use the cord for carrying, pulling 
or unplugging the power tool. 
Keep cord away from heat, oil, 
sharp edges or moving parts. 

Damaged or entangled cords 
increase the risk of electric shock.

e)  when operating a power tool 
outdoors, use an extension cord 
suitable for outdoor use. 

Use of 

a cord suitable for outdoor use 
reduces the risk of electric shock. 

f)  If operating a power tool in a 
damp location is unavoidable, use 
a residual current device (RCD) 
protected supply. 

Use of an RCD 

reduces the risk of electric shock. 

3. Personal safety

a)  stay alert, watch what you are 
doing and use common sense 
when operating a power tool. Do 
not use a power tool while you 
are tired or under the influence 
of drugs, alcohol or medication. 

A moment of inattention while 
operating power tools may result 
in serious personal injury. 

b)  use personal protective 
equipment. Always wear eye 
protection. 

Protective equipment 

such as dust mask, non-skid 

Summary of Contents for AG2200





























Reviews: