background image

13

21-18BLDD
Instruction & User Manual

OPERATING INSTRUCTIONS

Intended Use

This brushless drill driver is intended for drilling 
and screwing/unscrewing screws in wood, 
plastic and metal.
The tool must not be modified or used for 
any other purposes than the ones described in 
these instructions.

Battery

Make sure the power switch is not pressed 
in when inserting or replacing the battery. 
Use with JCB batteries only: 21-20LI, 21-
30LI, 21-40LI, 21-50LI.

NOTE

 

m

Do not force the battery when 
connecting it, use moderate pressure.

 

An incorrectly connected battery can 
damage the battery terminals or the battery 
socket on the tool.

 

m

Use the button on the battery to check the 
charging status; 4 red LEDs indicates fully 
charged, where 1 indicates low battery 
status.

Charging The Battery

After charging for the first time, ensure the 
battery is completely discharged before 
placing on charge again. Repeat this charging 
and discharging cycle 4 to 5 times to ensure 
battery is correctly conditioned.

WARNING!

 

m

Place the battery charger on a level and 
stable surface. Plug the charger into a 
suitable power point.

 

m

Connect the battery to the charger so that it 
clicks into place. 

 

m

Refer to the Battery Charge Level table 
below for battery charger status as indicated 
by LED lights.

 

m

Unplug the charger from the power point 
and remove the battery from the charger.

Battery Charge Level

Red 

LED

Green 

LED

Battery Charge Status

Charger is connected to 
mains power
Connected battery is 
charging
Connected battery is fully 
charged
Connected battery has a 
charging fault
Charger is outside correct 
operating temperature 
range  (<0˚C / >40˚C)

If the LEDs on the charger do not come on 
when charging:

 

m

Check that the charger’s mains plug is 
properly plugged into the power point and 
that the charger is switched on

 

m

Check that the battery is correctly inserted 
in the charger

Connecting the battery

 

m

Connect the battery to the battery socket 
on the tool so that it clicks into place.

Removing the battery

 

m

Press the battery release button and remove 
the battery from the tool.

Summary of Contents for 21-18BLDD





















Reviews: